Firstly I must apologise that I don't speak Italian
I'm based in Ireland, we have an office in Milano and I am trying to remotely configure a Cisco 837 to operate with Tiscali ADSL. I have referred this guide on Tiscalis website (note this is fior a Cisco 827, the config should be similar) buit I am unable to get the connection to work. The ATM interface picks up the line but the dialer will not work. See samples from config below - I would appreciete if someone could take a look to see if there are any errors:
Codice: Seleziona tutto
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Italy-backup
!
boot-start-marker
boot-end-marker
!
enable secret 5 <password>
enable password 7 <password>
!
no aaa new-model
!
resource policy
!
ip subnet-zero
!
!
no ip dhcp use vrf connected
!
!
ip cef
ip domain name <domain>
ip name-server <dns server>
no ip ips deny-action ips-interface
!
no ftp-server write-enable
!
!
interface Ethernet0
ip address <LAN IP address> 255.255.252.0
ip nat inside
ip virtual-reassembly
no cdp enable
hold-queue 100 out
!
interface Ethernet2
no ip address
shutdown
hold-queue 100 out
!
interface ATM0
no ip address
no ip mroute-cache
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface FastEthernet1
no ip address
duplex auto
speed auto
!
interface FastEthernet2
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet3
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet4
no ip address
shutdown
duplex auto
speed auto
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname [email protected]
ppp chap password 7 <password>
ppp pap sent-username [email protected] password 7 <password>
!
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Dialer1 overload
!
access-list 1 permit <LAN segment>
dialer-list 1 protocol ip permit
no cdp run
!
!
control-plane
!
!
line con 0
exec-timeout 0 0
no modem enable
stopbits 1
line aux 0
line vty 0 4
exec-timeout 120 0
password 7 <password>
login
!
scheduler max-task-time 5000
endCodice: Seleziona tutto
sh int di1
Dialer1 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address will be negotiated using IPCP
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi2
Last input never, output never, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Bound to:
Virtual-Access2 is up, [b]line protocol is down[/b]
Hardware is Virtual Access interface
MTU 1500 bytes, BW 0 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent
PPPoATM vaccess, cloned from Dialer1
Vaccess status 0x44
Bound to ATM0 VCD: 1, VPI: 8, VCI: 35, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Interface is bound to Di1 (Encapsulation PPP)
Last input never, output never, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
447739 packets output, 5372868 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitionsAny assistance appreciated.
CJ
Its an ADSL 2+ line (ITU G.992.5), however, the ATM interface detects ITU G.992.1 - is this not standard DSL? If so, does the 837 actually support ADSL2+, if not should I be looking at an 836?
