Wizard ha scritto:Intanto facci vedere la config che vediamo...
E cmq dimenticati della interfaccia web
Ecco quello che riesco a fare!
System Bootstrap, Version 12.2(11r)YV6, RELEASE SOFTWARE (fc1)
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C800/SOHO series (Board ID: 22-128) platform with 65536 Kbytes of main memory
program load complete, entry point: 0x80013000, size: 0x672b58
Self decompressing the image : #################################################
##################################################################### [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, Cal
Cisco IOS Software, SOHO97 Software (SOHO97-K9OY1-M), Version 12.4(5c), RELEASE
SOFTWARE (fc2)
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 01-Aug-07 23:22 by karnagar
Image text-base: 0x800131D0, data-base: 0x80BF948C
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco SOHO97 (MPC857DSL) processor (revision 0x500) with 58983K/6553K bytes of m
emory.
Processor board ID FCZ113223A5 (420360980), with hardware revision 5E5D
CPU rev number 7
1 Ethernet interface
1 ATM interface
128K bytes of NVRAM.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]:
Se:dico no:
Press RETURN to get started!
Do invio:
Mar 1 00:00:13.243: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
*Mar 1 00:00:14.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to up
*Mar 1 00:00:15.243: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 1 00:00:16.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
ged state to down
*Mar 1 00:05:52.907: %LINK-5-CHANGED: Interface Ethernet0, changed state to adm
inistratively down
*Mar 1 00:05:52.911: %LINK-5-CHANGED: Interface ATM0, changed state to administ
ratively down
*Mar 1 00:05:53.051: %SYS-5-RESTART: System restarted --
Cisco IOS Software, SOHO97 Software (SOHO97-K9OY1-M), Version 12.4(5c), RELEASE
SOFTWARE (fc2)
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 01-Aug-07 23:22 by karnagar
*Mar 1 00:05:53.051: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing
a cold start
*Mar 1 00:05:54.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to down
(E si blocca)do invio e:
Router>
Se invece dico si:
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]:
Yes:
Configuring global parameters:
Enter host name [Router]:
Io inserisco un nome a caso: principio
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Io inserisco 1c2345
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password:
io inserisco 1c23456
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password:
io inserisco 1c234567
Configure SNMP Network Management? [yes]:
io dico di no,non mi interessa
Current interface summary
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Prot
ocol
Ethernet0 unassigned NO unset up up
ATM0 unassigned NO unset down down
Enter interface name used to connect to the
management network from the above interface summary:
io scrivo: Ethernet0
Configuring interface Ethernet0:
Configure IP on this interface? [yes]:
io dico :si
gli imposto ip 192.168.1.71
sh verphic feature
Router#sh verphic feature
IP address for this interface: 192.168.1.71y the Government is Software (SOHO97-K9OY1-M),
Subnet mask for this interface [255.255.255.0] :
enable password 1c23456
line vty 0 4
password 1c234567
no snmp-server
!
no ip routing
!
interface Ethernet0
no shutdown
ip address 192.168.1.71 255.255.255.0
!
interface ATM0
shutdown
no ip address
!
end
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
Enter your selection [2]:
scrivo 2
uilding configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
*Mar 1 00:00:13.239: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
*Mar 1 00:00:14.243: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0,
changed state to up
*Mar 1 00:00:15.239: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 1 00:00:16.243: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, chan
ged state to down
*Mar 1 00:14:37.347: %LINK-5-CHANGED: Interface ATM0, changed state to administ
ratively down
*Mar 1 00:05:53.019: %SYS-5-RESTART: System restarted --
Cisco IOS Software, SOHO97 Software (SOHO97-K9OY1-M), Version 12.4(5c), RELEASE
SOFTWARE (fc2)
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 01-Aug-07 23:22 by karnagar
*Mar 1 00:05:53.023: %SNMP-5-COLDSTART: SNMP agent on host principio is undergo
ing a cold start
si blocca ,io do invio e:
principio>
dopo un pochino mi dice:
*Mar 1 00:09:16.523: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on Ethe
rnet0 (not half duplex), with SEP001AA1251B3A Port 1 (half duplex).
*Mar 1 00:10:16.555: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on Ethe
rnet0 (not half duplex), with SEP001AA1251B3A Port 1 (half duplex).
*Mar 1 00:11:16.603: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on Ethe
rnet0 (not half duplex), with SEP001AA1251B3A Port 1 (half duplex).
Ma se riavvio ricomincia tutto da capo!!
