EDIT - 827H & QoS Priority Queuing

[metalgalle]

Ciao Gente,
come da manuale Cisco (vedi sito http://www.cisco.com/en/US/docs/ios/12_ ... tml#wp5112) ho configurato quanto segue:

Codice: Seleziona tutto

priority-list 1 protocol ip low tcp 65535
priority-list 1 protocol ip low udp 65535
priority-list 1 protocol ip low tcp 65534
priority-list 1 protocol ip low udp 65534

solo che al momento di associare la priorità ad una interfaccia (ex. dialer0) con il comando

Codice: Seleziona tutto

int dialer0
priority-group 1

il fetentone non mi riconosce il comando priority-group...

Di seguito uno show ver:

***
Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-OY6-M), Version 12.2(4)YA4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 27-Dec-02 11:28 by ealyon
Image text-base: 0x80013170, data-base: 0x806AA244

ROM: System Bootstrap, Version 12.2(4r)XM2, RELEASE SOFTWARE (fc1)
ROM: C820 Software (C820-OY6-M), Version 12.2(4)YA4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

827H uptime is 17 hours, 21 minutes
System returned to ROM by power-on
System image file is "flash:c820-oy6-mz.122-4.YA4.bin"

CISCO C827H (MPC855T) processor (revision 0x501) with 31744K/1024K bytes of memory.
Processor board ID FOC07140ZSG (2973082481), with hardware revision 0000
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)

Configuration register is 0x2101
***


WHY?????? Becchè?????? Perdinci.....


Grassie a tutti in anticipo!

Bye!

[metalgalle]

Sono arrivato ad un buon punto, ho aggiornato l'IOS ed ecco che i comandi latitanti sono comparsi.

Vorrei solo avere una delucidazione da parte Vs.: volendo dare priorità ad una tipologia di traffico o un'altra qual'è la soluzione più indicata secondo voi?

Fino ad oggi (sui router bintec) ho utilizzato il PQ, ma la conf di Cisco mi lascia qualche dubbio, non sono sicuro se stia funzando correttamente.

Posto uno stralcio, ditemi se secondo voi è corretta:

Codice: Seleziona tutto

interface Ethernet0
 ip address 10.79.1.253 255.255.255.0
 ip nat inside
 priority-group 1
 no cdp enable
!
interface ATM0
 no ip address
 no atm ilmi-keepalive
 dsl operating-mode auto
 pvc 8/35
  encapsulation aal5mux ppp dialer
  dialer pool-member 1
 !
!
interface Dialer0
 ip address negotiated
 ip nat outside
 encapsulation ppp
 dialer pool 1
 priority-group 2
 no cdp enable
 ppp chap password 7 XXXXX
 ppp pap sent-username XXXX
!
ip nat inside source list 2 interface Dialer0 overload
ip nat inside source static tcp 10.79.1.254 3389 interface Dialer0 3389
ip nat inside source static tcp 10.79.1.254 443 interface Dialer0 443
ip nat inside source static udp 10.79.1.254 65535 interface Dialer0 65535
ip nat inside source static tcp 10.79.1.254 65535 interface Dialer0 65535
ip nat inside source static udp 10.79.1.254 65534 interface Dialer0 65534
ip nat inside source static tcp 10.79.1.254 65534 interface Dialer0 65534
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 10.79.0.0 255.255.255.0 10.79.1.254
no ip http server
no ip http secure-server
!
access-list 2 permit 10.79.1.254

priority-list 1 protocol ip low tcp 65535
priority-list 1 protocol ip low udp 65535
priority-list 1 protocol ip low tcp 65534
priority-list 1 protocol ip low udp 65534
priority-list 1 protocol ip high tcp 443
priority-list 2 protocol ip high tcp 443

Bye!