router cisco 1721

[aghibear]

ciao a tutti,
quando accendo l mio router,ad un certo punto mi compaiono queste 3 righe:
%Error opening tftp://255.255.255.255/network-confg (Timed out)
%Error opening tftp://255.255.255.255/cisconet.cfg (Timed out)
%Error opening tftp://255.255.255.255/alto-confg (Timed out)
anche quando sono in privileg mode.
come posso evitare che il router vada a cercare con il tftp???

grazie a tutti

aghibear

[djdylan78]

Se non erro tutto sta nel valore del registro quello 0x2102 e simili, in base a quel valore il router cerca di caricare la config da un determinato posto o altro

[aghibear]

ciao,
vado a verificare la conf del registro

grazie

[agilulfo_emo]

ho letto un sacco di robba per produrre questo. sono accettati suggerimenti, rimproveri...
Pare che funzioni, sulla qos non ci metterei la mano sul fuoco.
Comunque, a qualcuno potrebbe essere sempre utile


!
version 12.2
service config
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname ________
!
enable secret 5 *********
enable password *********
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
!
!
ip name-server 212.216.112.112
ip name-server 212.216.172.62
ip dhcp excluded-address 192.168.0.10
!
ip dhcp pool C_addr
network 192.168.0.0 255.255.255.0
default-router 192.168.0.254
dns-server 212.216.112.112 212.216.172.62
!
ip dhcp pool GATSU ! Danilo con il mulo ip manuale
host 192.168.0.10 255.255.255.0
client-identifier 0100.08a1.3c76.25
client-name GATSU
!
ip cef
!
class-map match-any giochi
match access-group name soldier_of_fortune
class-map match-any WebEmail
match protocol http
match protocol secure-http
match protocol ftp
match protocol smtp
match protocol pop3
class-map match-any VoIP
match access-group name per_skype
match access-group name per_SIP
!
!
policy-map MyPolicyMap
class VoIP
priority percent 60
class giochi
bandwidth remaining percent 50
class WebEmail
bandwidth remaining percent 40
class class-default
fair-queue
!
!
!
!
interface ATM0
no ip address
no ip mroute-cache
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5snap
protocol ppp dialer
dialer pool-member 1
!
dsl operating-mode auto
no fair-queue
hold-queue 224 in
!
interface Ethernet0
no ip address
shutdown
half-duplex
!
interface FastEthernet0
description connected to EthernetLAN
ip address 192.168.0.254 255.255.255.0
ip nat inside
no ip route-cache
no ip mroute-cache
speed auto
full-duplex
no cdp enable
!
interface Dialer0
bandwidth 256
ip address negotiated
ip access-group 101 in
ip nat outside
ip nbar protocol-discovery
encapsulation ppp
dialer pool 1
dialer-group 1
service-policy output MyPolicyMap
ppp authentication pap callin
ppp pap sent-username ****** password 0 *****
!
ip nat inside source list 101 interface Dialer0 overload
ip nat inside source static udp 192.168.0.10 20100 interface Dialer0 20100
ip nat inside source static tcp 192.168.0.10 4662 interface Dialer0 4662
ip nat inside source static udp 192.168.0.10 4672 interface Dialer0 4672
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
ip pim bidir-enable
!
!
ip access-list extended per_skype
permit udp any any range 54045 54050
ip access-list extended per_SIP
permit udp any any eq 5060
ip access-list extended soldier_of_fortune
permit udp any any range 20100 20110
!
access-list 101 deny icmp any any redirect
access-list 101 deny icmp any any information-request
access-list 101 permit udp any host 212.216.112.112 eq domain
access-list 101 permit udp any host 212.216.172.62 eq domain
access-list 101 permit udp host 212.216.112.112 eq domain any
access-list 101 permit udp host 212.216.172.62 eq domain any
access-list 101 permit tcp 192.168.0.0 0.0.0.255 any
access-list 101 permit tcp any any eq 4662
access-list 101 permit udp any any eq 4672
access-list 101 permit udp any any range 20100 20110
access-list 101 permit udp any any eq 5060
access-list 101 permit tcp any any established
!
snmp-server community public RO
!
line con 0
exec-timeout 0 0
line aux 0
line vty 0 4
password *****
login
!
no scheduler allocate
end

Grazie e ciao a tutti.

[Wizard]

devi fare uno "sh ver" per vedere la config del registro

[Gibo®]

copy running-config startup-config

reload

ciacciao!
)

[slaider]

la soluzione è semplice

config terminal
no service config
exit
copy running-config startup-config

Ciao

[anaconda]

Hai sbagliato il mask 255.255.255.255. non esiste metti 255.255.255.0
ciao