Linea ATM non si aggancia: router Cisco 857

[cristianoburgo]

Ho due router cisco 857.
Uno funziona e si aggancia l'altro no.
Vi posto lo stato delle interfaccie:

Il router che non va:

ATM0 is initializing, line protocol is down
Hardware is MPC ATMSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 4608 Kbit, DLY 80 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 1024 VCs per VP, 0 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
ATM0.1 is initializing, line protocol is down
Hardware is MPC ATMSAR (with Alcatel ADSL Module)
Description: $ES_WAN$$FW_OUTSIDE$
Internet address is xxx.xxx.xxx.xxx/30
MTU 4470 bytes, BW 4608 Kbit, DLY 80 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
0 packets input, 0 bytes
0 packets output, 0 bytes
0 OAM cells input, 0 OAM cells output
AAL5 CRC errors : 0
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 0
Last clearing of "show interface" counters never

Il router che va:

ATM0 is up, line protocol is up
Hardware is MPC ATMSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 320 Kbit, DLY 1150 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 1024 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input 1d15h, output 00:00:03, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
230 packets input, 14303 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3914 packets output, 236635 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 output buffer failures, 0 output buffers swapped out
ATM0.1 is up, line protocol is up
Hardware is MPC ATMSAR (with Alcatel ADSL Module)
Description: $ES_WAN$$FW_INSIDE$
Internet address is xxx.xxx.xxx.202/30
MTU 4470 bytes, BW 128 Kbit, DLY 1150 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
230 packets input, 14303 bytes
273 packets output, 47303 bytes
3641 OAM cells input, 3641 OAM cells output
AAL5 CRC errors : 0
AAL5 SAR Timeouts : 0
AAL5 Oversized SDUs : 0
Last clearing of "show interface" counters never

Vi voglio far notare che al router che funziona c'è in ATM0 :
BW 320 Kbit, DLY 1150 usec

Mentre a quello che non va c'è:
BW 4608 Kbit, DLY 80 usec

è questo il problema ???? e se si come si fa a risolverlo ??

Configurazioni delle interfacce:


Router che non va:

interface ATM0
no ip address
ip route-cache flow
no atm ilmi-keepalive
dsl operating-mode ansi-dmt
!
interface ATM0.1 point-to-point
bandwidth 128
description $ES_WAN$$FW_OUTSIDE$
ip address ddd.xxx.yyy.zzz 255.255.255.252
ip nat outside
ip virtual-reassembly
pvc 8/35
oam-pvc manage
oam retry 5 5 1
encapsulation aal5snap
!

Router che va:

interface ATM0
no ip address
ip route-cache flow
no atm ilmi-keepalive
dsl operating-mode ansi-dmt
!
interface ATM0.1 point-to-point
description $ES_WAN$$FW_INSIDE$
bandwidth 128
ip address ddd.xxx.yyy.zzz 255.255.255.252
ip inspect DEFAULT100 in
ip nat outside
ip virtual-reassembly
pvc 8/35
oam-pvc manage
oam retry 5 5 1
encapsulation aal5snap
!
!

[MaiO]

Ma la portante c'è??!?!

A vedere l'interfaccie su quello che non va non credo ci sia.

Contatta il tuo provider.


Ciao

[marchino65]

Ciao,
presumo che tu stia parlando di due siti diversi visto gli indirizzi delle punto/punto.
Prova a cambiare la riga da:
dsl operating-mode ansi-dmt
a
dsl operating-mode auto

I valori di BW sono diversi, perchè non ha sentito la portante
Ciao

[cristianoburgo]

Non va ancora ... Allora è un problema telecom o posso cavarmela in un altra maniera ?

[cristianoburgo]

ho portato il router che funziona nell'altra sede ... e si aggancia quindi la linea funziona.

Non è che è sto SDM (configuratore web del router) che fa i capricci ?????
Ognni tanto mi compaiono dei file sul desktop del tipo :

hs_err_pid5092 con dei mess di debug di java ...

[marchino65]

Ciao,
come ti ho scritto in privato, se mi dai la tgu, ti controllo se ci sono problemi sulla linea.

Saluti

[cristianoburgo]

Il problema era la versione dell'ios !!!!!
Mi hanno dato la versione:

c850-advsecurityk9-mz.124-4.T1

e ha funzionato ...



ole !!!!