ho un disperato bisogno di aiuto.
avevo un cisco 878 che con un temporale si è bruciato, ho assemblato un csco 2610 con una vic shdsl v2 per ripristinare la mia connessione, ma non capisco come configurare la scheda.
per l' 878 avevo trovato tutto su internet e funzionava benissimo qui non so come cavarmela.
questa la configurazione del 878
version 12.3
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname router
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$EKhr$I1wv3EIN23HzeryXln9JX/
!
username router password 7 101D5B150E114B531B15
no aaa new-model
ip subnet-zero
!
!
ip name-server 213.205.32.70
ip name-server 213.205.36.70
!
!
!
interface Ethernet0
ip address 82.85.*.* 255.255.255.240
ip virtual-reassembly
no ip mroute-cache
hold-queue 100 out
!
interface ATM0
no ip address
no ip mroute-cache
atm vc-per-vp 64
no atm ilmi-keepalive
dsl equipment-type CPE
dsl operating-mode GSHDSL symmetric annex A
dsl linerate AUTO
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname *************@tiscali.it
ppp chap password 7 0553505D70181F
ppp pap sent-username ********@tiscali.it password 7 144F44595D507B
hold-queue 224 in
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip nat inside source list 102 interface Dialer1 overload
!
!
access-list 102 permit ip 82.85.*.* 0.0.0.15 any
dialer-list 1 protocol ip permit
!
control-plane
!
!
line con 0
exec-timeout 120 0
stopbits 1
line vty 0 4
exec-timeout 120 0
login local
length 0
!
scheduler max-task-time 5000
end
e questa quella dell' attuale 2610
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
no ip dhcp use vrf connected
!
!
no ip ips deny-action ips-interface
ip name-server 213.205.32.70
ip name-server 213.205.36.70
!
!
!
!
!
!
controller DSL 0/1
line-term cpe
!
!
!
!
interface Ethernet0/0
ip address 82.85.*.* 255.255.255.240
ip virtual-reassembly
no ip mroute-cache
half-duplex
hold-queue 100 out
!
interface Serial0/0
no ip address
shutdown
!
ip classless
!
ip http server
no ip http secure-server
!
!
!
control-plane
!
!
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end
qui mi blocco. Ho provato ad inserire i comandi per l'ATM ma non ne funziona nessuno e non so come continuare.
per cortesia aiutatemi
grazie
