PPPoA con 837 (ios 12.2) - problema nella configurazione

Configurazioni per connettività ADSL, ISDN e switch per privati e piccole network

Moderatore: Federico.Lagni

Rispondi
pinkblues
n00b
Messaggi: 1
Iscritto il: mer 05 mag , 2010 9:48 pm

Ciao a tutti
E' il mio primo messaggio del forum :-)
Ho spulciato in lungo e largo e sono riuscito a costruire a spizzichi e bocconi una configurazione per il PPPoA con Tiscali (ip dinamico).
Purtroppo il router però non si collega.
Sareste cortesemente in grado di dirmi dove ho sbagliato
Grazie in anticipo

Codice: Seleziona tutto

Current configuration : 2393 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log uptime
service password-encryption
!
logging queue-limit 100
enable secret 5 xxxx
!
username checkline
username checkline autocommand show controller atm
username infocisco password 7 xxxxx
clock timezone met 1
clock summer-time MET+1 recurring last Sun Mar 2:00 last Sun Oct 3:00
aaa new-model
!
aaa authentication login CONSOLE enable
aaa authentication login TELNET local
aaa authentication ppp default none
aaa authorization exec CONSOLE none
aaa authorization exec TELNET local
aaa session-id common
ip subnet-zero
no ip domain lookup
ip domain name tiscali.it
ip name-server 213.205.32.70
ip name-server 213.205.36.70
ip dhcp excluded-address 192.168.240.1
!
ip dhcp pool LOCAL
   network 192.168.240.0 255.255.255.0
   default-router 192.168.240.1
   dns-server 213.205.32.70 213.205.36.70
!
ip multicast-routing
ip audit notify log
ip audit po max-events 100
no ftp-server write-enable
!
interface Ethernet0
 ip address 192.168.240.1 255.255.255.0
 ip nat inside
 ip pim sparse-dense-mode
 no ip route-cache
 no ip mroute-cache
 hold-queue 100 out
!
interface ATM0
 no ip address
 no ip mroute-cache
 no atm ilmi-keepalive
 dsl operating-mode itu-dmt   (ho provato anche AUTO, ma stesso discorso)
 hold-queue 224 in
!
interface ATM0.1 point-to-point
 pvc 8/35
  encapsulation aal5mux ppp dialer  
  dialer pool-member 1
 !
!
interface Dialer0
 ip address negotiated
 ip pim sparse-dense-mode
 encapsulation ppp
 dialer pool 1
 dialer-group 1
 ppp authentication pap callin
 ppp chap refuse
 ppp pap sent-username USER password 7 PASSWORD
!
ip nat inside source list 101 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
!
access-list 101 permit ip 192.168.240.0 0.0.0.255 any
dialer-list 1 protocol ip permit
snmp-server community cominfo RO 4
snmp-server packetsize 484
snmp-server trap-timeout 60
snmp-server enable traps tty
radius-server authorization permit missing Service-Type
!
line con 0
 authorization exec CONSOLE
 login authentication CONSOLE
 no modem enable
 stopbits 1
line aux 0
 stopbits 1
line vty 0 4
 access-class 3 in
 exec-timeout 0 0
 authorization exec TELNET
 login authentication TELNET
!
scheduler max-task-time 5000
!
end
####### quando agganco il cavo DSL, compaiono questi

Codice: Seleziona tutto

00:22:18: %DIALER-6-BIND: Interface Vi2 bound to profile Di0
00:22:18: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
00:22:19: %LINK-3-UPDOWN: Interface ATM0, changed state to up
00:22:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up
####### se faccio show interface compaiono questi

Codice: Seleziona tutto

ATM0 is up, line protocol is up
  Hardware is PQUICC_SAR (with Alcatel ADSL Module)
  MTU 1500 bytes, sub MTU 1500, BW 640 Kbit, DLY 80 usec,
     reliability 40/255, txload 1/255, rxload 1/255
  Encapsulation ATM, loopback not set
  Encapsulation(s): AAL5  AAL2, PVC mode
  10 maximum active VCs, 1024 VCs per VP, 1 current VCCs
  VC Auto Creation Disabled.
  VC idle disconnect time: 300 seconds
  Last input never, output 00:00:01, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: Per VC Queueing
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     19 packets output, 304 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 output buffer failures, 0 output buffers swapped out
ATM0.1 is up, line protocol is up
  Hardware is PQUICC_SAR (with Alcatel ADSL Module)
  MTU 1500 bytes, BW 800 Kbit, DLY 80 usec,
     reliability 40/255, txload 1/255, rxload 1/255
  Encapsulation ATM
  0 packets input, 0 bytes
  20 packets output, 320 bytes
  0 OAM cells input, 0 OAM cells output
  AAL5 CRC errors : 0
  AAL5 Oversized SDUs : 0
  Last clearing of "show interface" counters never
Dialer0 is up, line protocol is up (spoofing)
  Hardware is Unknown
  Internet address will be negotiated using IPCP
  MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, loopback not set
  DTR is pulsed for 1 seconds on reset
  Interface is bound to Vi2
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 00:23:12
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops)
     Conversations  0/0/16 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
     Available Bandwidth 42 kilobits/sec
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes
     0 packets output, 0 bytes
Bound to:
Virtual-Access2 is up, line protocol is down
  Hardware is Virtual Access interface
  MTU 1500 bytes, BW 56 Kbit, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Listen
  PPPoATM vaccess, cloned from Dialer0
  Bound to ATM0.1 VCD: 1, VPI: 8, VCI: 35, loopback not set
  DTR is pulsed for 5 seconds on reset
  Interface is bound to Di0 (Encapsulation PPP)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 00:01:13
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     20 packets output, 240 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
Ethernet0 is up, line protocol is up
  Hardware is PQUICC Ethernet, address is 000f.8fe7.e867 (bia 000f.8fe7.e867)
  Internet address is 192.168.240.1/24
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  Full-duplex, 10Mb/s
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output 00:00:02, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/100 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     263 packets output, 24948 bytes, 0 underruns
     0 output errors, 0 collisions, 6 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Virtual-Access1 is up, line protocol is up
  Hardware is Virtual Access interface
  MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Base PPPoATM vaccess, loopback not set
  DTR is pulsed for 5 seconds on reset
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 00:23:24
  Input queue: 0/4096/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
Virtual-Access2 is up, line protocol is down
  Hardware is Virtual Access interface
  MTU 1500 bytes, BW 56 Kbit, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation PPP, LCP Listen
  PPPoATM vaccess, cloned from Dialer0
  Bound to ATM0.1 VCD: 1, VPI: 8, VCI: 35, loopback not set
  DTR is pulsed for 5 seconds on reset
  Interface is bound to Di0 (Encapsulation PPP)
  Last input never, output never, output hang never
  Last clearing of "show interface" counters 00:01:32
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     20 packets output, 240 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
#########Show IP Interface

Codice: Seleziona tutto

ATM0 is up, line protocol is up
  Internet protocol processing disabled
ATM0.1 is up, line protocol is up
  Internet protocol processing disabled
Dialer0 is up, line protocol is up
  Internet address will be negotiated using IPCP
  Broadcast address is 255.255.255.255
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Multicast reserved groups joined: 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is enabled
  IP fast switching on the same interface is enabled
  IP Flow switching is disabled
  IP CEF switching is disabled
  IP Feature Fast switching turbo vector
  IP multicast fast switching is enabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are Fast
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is disabled
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
  BGP Policy Mapping is disabled
Ethernet0 is up, line protocol is up
  Internet address is 192.168.240.1/24
  Broadcast address is 255.255.255.255
  Address determined by non-volatile memory
  MTU is 1500 bytes
  Helper address is not set
  Directed broadcast forwarding is disabled
  Multicast reserved groups joined: 224.0.0.1 224.0.0.2 224.0.0.22 224.0.0.13
  Outgoing access list is not set
  Inbound  access list is not set
  Proxy ARP is enabled
  Local Proxy ARP is disabled
  Security level is default
  Split horizon is enabled
  ICMP redirects are always sent
  ICMP unreachables are always sent
  ICMP mask replies are never sent
  IP fast switching is disabled
  IP fast switching on the same interface is disabled
  IP Flow switching is disabled
  IP CEF switching is disabled
  IP Feature Fast switching turbo vector
  IP multicast fast switching is disabled
  IP multicast distributed fast switching is disabled
  IP route-cache flags are None
  Router Discovery is disabled
  IP output packet accounting is disabled
  IP access violation accounting is disabled
  TCP/IP header compression is disabled
  RTP/IP header compression is disabled
  Policy routing is disabled
  Network address translation is enabled, interface in domain inside
  WCCP Redirect outbound is disabled
  WCCP Redirect inbound is disabled
  WCCP Redirect exclude is disabled
  BGP Policy Mapping is disabled
Virtual-Access1 is up, line protocol is up
  Internet protocol processing disabled
Virtual-Access2 is up, line protocol is down
  Internet protocol processing disabled
Rispondi