Salve come posso configurare una connessione aggiuntiva di tipo bridge 8/36 sul soho 97?
Router con0 is now available
Press RETURN to get started.
Router>configure terminal
^
% Invalid input detected at '^' marker.
Router>enable
Password:
Router#show dsl int atm0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'GSPN'
Vendor Specific: 0x0000 0x0008
Vendor Country: 0x00 0xFF
Capacity Used: 92% 76%
Noise Margin: 15.5 dB 20.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 16.0 dB 9.5 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 2589 (4 spurious)
Activations: 5
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.220
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 7616 0 480 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 1 0
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface atm0
Router(config-if)#dsl noise-margin -8
Router(config-if)#
3d00h: %LINK-3-UPDOWN: Interface ATM0, changed state to down
3d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to do
wn
Router(config-if)#exit
Router(config)#exit
Router#
3d00h: %SYS-5-CONFIG_I: Configured from console by console
3d00h: %LINK-3-UPDOWN: Interface ATM0, changed state to up
3d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up
Router#show dsl int atm0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'GSPN'
Vendor Specific: 0x0000 0x0008
Vendor Country: 0x00 0xFF
Capacity Used: 92% 76%
Noise Margin: 15.5 dB 20.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 16.0 dB 9.5 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 3235 (5 spurious)
Activations: 6
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.220
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 7616 0 480 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 1 0
Header Errors: 0 0 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0
LOM Monitoring : Disabled
DMT Bits Per Bin
00: 0 0 0 0 0 0 0 3 4 5 7 7 8 8 9 8
10: 8 8 8 8 8 7 7 7 6 6 5 5 5 5 0 0
20: 0 0 0 0 0 0 6 7 8 8 9 9 A A B B
30: B B B C C C C C C C C C C C C C
40: 0 C C C C C C C C C 2 C C C C C
50: C C C C C C C C C C C C B B B B
60: B B B B B B B A A A A A A A B A
70: A A A A A A A A A A A A A A A B
80: A A A A B B B B A B B B A B A B
90: B B B B B B B B B B A B B B A A
A0: B B B B B B B B B B B B B B B B
Router#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Router#
Router#sh atm interface atm 0
Interface ATM0:
AAL enabled: AAL5 AAL2, Maximum VCs: 10, Current VCCs: 1
VCIs per VPI: 64,
Max. Datagram Size: 1528
PLIM Type: ADSL - 800Kbps Upstream, DMT, TX clocking: LINE
75402 input, 7 output, 6443124 IN fast, 6394627 OUT fast
Avail bw = 800
Config. is ACTIVE
Router#show interface dsl
^
% Invalid input detected at '^' marker.
Router#show interface atm0
ATM0 is up, line protocol is up
Hardware is PQUICC_SAR (with Alcatel ADSL Module)
MTU 1500 bytes, sub MTU 1500, BW 480 Kbit, DLY 80 usec,
reliability 255/255, txload 1/255, rxload 13/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 64 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input 00:03:27, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 90519
Queueing strategy: Per VC Queueing
5 minute input rate 26000 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
6519442 packets input, 3886473889 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 5 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
6624140 packets output, 3656827838 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 output buffer failures, 0 output buffers swapped out
Router#
Router#show dsl int atm 0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'GSPN'
Vendor Specific: 0x0000 0x0008
Vendor Country: 0x00 0xFF
Capacity Used: 92% 76%
Noise Margin: 15.5 dB 20.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 16.5 dB 9.5 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 3235 (5 spurious)
Activations: 6
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.220
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 7616 0 480 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 1 0
Header Errors: 0 0 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0
LOM Monitoring : Disabled
DMT Bits Per Bin
00: 0 0 0 0 0 0 0 3 4 5 7 7 8 8 9 8
10: 8 8 8 8 8 7 7 7 6 6 5 5 5 5 0 0
20: 0 0 0 0 0 0 7 7 8 8 9 9 A A B B
30: B B B C C C C C C C C C C C C C
40: 0 C C C C C C C C C 2 C C C C C
50: C C C C C C C C C C C C B B B B
60: B B B B B B B A A A A A A A B A
70: A A A A A A A A A A A A A A A B
80: A A A A B B B B A B B B A B A B
90: B B B B B B B B B B A B B B A A
A0: B B B B B B B B B B B B B B B B
B0: B B B B B B A B B B A B B B B B
C0: A A A A A A A A A A A A A A A A
D0: A A A A A A A A A A A 9 A 9 9 9
E0: 9 9 9 9 9 9 9 9 9 8 8 8 8 8 8 8
F0: 8 7 7 7 7 0 0 0 0 0 0 0 0 0 0 0
Training log buffer capability is not enabled yet.
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#
Router#exit
Router con0 is now available
Press RETURN to get started.
Router>
Router>
Router>enable
Password:
Router#show running-config
Building configuration...
Current configuration : 3389 bytes
!
version 12.4
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
service internal
!
hostname Router
!
boot-start-marker
boot-end-marker
!
no logging buffered
enable secret 5 $1$.fUE$x2yGe8RZFIWBPTyoLTlx/0
!
no aaa new-model
!
resource policy
!
ip dhcp excluded-address 10.10.10.30
ip dhcp excluded-address 10.10.10.25
ip dhcp excluded-address 10.10.10.2
!
!
ip cef
ip domain name cisco.com
ip name-server 208.67.222.222
ip name-server 212.216.112.112
ip inspect name myfw cuseeme timeout 3600
ip inspect name myfw ftp timeout 3600
ip inspect name myfw rcmd timeout 3600
ip inspect name myfw realaudio timeout 3600
ip inspect name myfw smtp timeout 3600
ip inspect name myfw tftp timeout 30
ip inspect name myfw udp timeout 15
ip inspect name myfw tcp timeout 3600
ip inspect name myfw h323 timeout 3600
!
username Router password 7 02340B4E1F031D
!
!
!
!
interface Ethernet0
ip address 10.10.10.1 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
hold-queue 100 out
!
interface ATM0
no ip address
atm vc-per-vp 64
no atm ilmi-keepalive
dsl operating-mode auto
dsl noise-margin -3
pvc 8/35
oam-pvc 0
pppoe-client dial-pool-number 1
!
!
interface Dialer1
ip address negotiated
ip access-group 111 in
ip mtu 1492
ip nat outside
ip inspect myfw out
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer remote-name redback
dialer-group 1
ppp authentication pap chap callin
ppp chap hostname aliceadsl
ppp chap password 7 1218091E110E0D003927
ppp pap sent-username aliceadsl password 7 13041B1B0809052E3828
!
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
ip dns server
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static udp 10.10.10.30 4762 interface Dialer1 4762
ip nat inside source static tcp 10.10.10.30 4662 interface Dialer1 4662
ip nat inside source static udp 10.10.10.25 5061 interface Dialer1 5061
ip nat inside source static udp 10.10.10.2 5060 interface Dialer1 5060
!
access-list 23 permit 10.10.10.0 0.0.0.255
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
access-list 111 permit udp any any eq 4762
access-list 111 permit tcp any any eq 4662
access-list 111 permit udp any any eq 5061
access-list 111 permit udp any any eq 5060
access-list 111 permit icmp any any administratively-prohibited
access-list 111 permit icmp any any echo
access-list 111 permit icmp any any echo-reply
access-list 111 permit icmp any any packet-too-big
access-list 111 permit icmp any any time-exceeded
access-list 111 permit icmp any any traceroute
access-list 111 permit icmp any any unreachable
access-list 111 permit udp any eq bootps any eq bootpc
access-list 111 permit udp any eq bootps any eq bootps
access-list 111 permit udp any eq domain any
access-list 111 permit esp any any
access-list 111 permit udp any any eq isakmp
access-list 111 permit udp any any eq 10000
access-list 111 permit tcp any any eq 1723
access-list 111 permit tcp any any eq 139
access-list 111 permit udp any any eq netbios-ns
access-list 111 permit udp any any eq netbios-dgm
access-list 111 permit gre any any
access-list 111 deny ip any any
dialer-list 1 protocol ip permit
!
control-plane
!
!
line con 0
exec-timeout 0 0
no modem enable
stopbits 1
line aux 0
line vty 0 4
access-class 23 in
exec-timeout 0 0
login local
length 0
!
scheduler max-task-time 5000
end
configurare 2 pvc con soho97
Moderatore: Federico.Lagni
