problema rommon cisco 1921

[alexmio]

Ciao a tutti.

Ho un problema con un cisco 1921

al avvio mi da questo :


System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.

Total memory size = 512 MB
CISCO1921/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC disabled


Readonly ROMMON initialized
program load complete, entry point: 0x80903000, size: 0x4c4a0
program load complete, entry point: 0x80903000, size: 0x4c4a0

loadprog: error - on load of image from file system with monlib
boot: cannot load "usbflash0:"

System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.

Total memory size = 512 MB
CISCO1921/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC disabled


Readonly ROMMON initialized
open(): Open Error = -1
usbflash1: not present

System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsuppo
Copyright (c) 2011 by cisco Systems, Inc.

Total memory size = 512 MB
CISCO1921/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC disabled


Readonly ROMMON initialized
program load complete, entry point: 0x80903000, size: 0x4c4a0
program load complete, entry point: 0x80903000, size: 0x4c4a0

loadprog: error - on load of image from file system with monlib
boot: cannot load "usbflash0:"

System Bootstrap, Version 15.0(1r)M12, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2011 by cisco Systems, Inc.

Total memory size = 512 MB
CISCO1921/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC disabled


Readonly ROMMON initialized
rommon 1 >
rommon 1 > confreg


Configuration Summary
(Virtual Configuration Register: 0x2102)
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-CISCO1921/K9

do you wish to change the configuration? y/n [n]: n


rommon 2 > dev
Devices in device table:
id name
flash: usbflash0
bootflash: boot flash
usbflash0: usbflash0
usbflash1: usbflash1
eprom: eprom
rommon 3 > dir flash:
program load complete, entry point: 0x80903000, size: 0x4c4a0
Directory of flash:

2 45821644 -rw- c1900-universalk9-mz.SPA.150-1.M7.bin
rommon 4 > boot flash:c1900-universalk9-mz.SPA.150-1.M7.bin
program load complete, entry point: 0x80903000, size: 0x4c4a0

loadprog: error - on load of image from file system with monlib
boot: cannot load "flash:c1900-universalk9-mz.SPA.150-1.M7.bin"
rommon 5 >

non so cosa fare per ripristinare la situazione, mi basterebbe riportarlo a factory defaults non mi importa della configurazione. questo è un 1921 sec K9 , provando a far partire ios dal usb non mi da securityk9 abilitato.

Grazie a tutti.

[Rizio]

Non può esserti partita la flash?
In rommon hai per caso dei comandi per verificare il filesystem?
Perchè io proverei a far avvirare il router con qualsiasi ios via rete (tftp), poi, da lì verificherei bene la flash o il fs.

Rizio