CiscoForums.it

Buon giorno, sono nuovo e mi diletto nel cercare di programmare i miei due router Cisco "ereditati" (un 827 ed un 877).

Vi chiedo aiuto in quanto ho dei problemi di "allineamneto" tra i Cisco e la nuova "macchina" Dslam da poco installata nel mio paese.

spiego:

dopo che Telecom (Alice 7MBit) aveva "overbooking" i loro dslam e sentito un vagone di insulti;
ha finalmente deciso di aggiungere un ulteriore dslam (scopro made in Cina) per rendere "onesta" la navigazione (io abito a ~ 1.5 Km dalla centrale tel. e viaggiavo tra i 1.5 ed i 2.5 Mbit).

In effetti con l'aggiunta della nuova "macchina" il cambiamento c'é stato (ora ho un download ~ 5 - 6 Mbit).

Unico problema, ho grosse difficoltà di "allieamento", cioé prima che il CD ed il PPP si accenda fisso, devo:
spegnere /accendere diverse volte e pregare molto.

Una volta "allineato" funziona onestamente e raramente si scollega.

Con un router telecom (Alice gate 2 Plus WIFI) il problema non sussiste.

Chiamato telecom, questa mi ha controllato la linea rame, indicandomi una attenuazione di 31 dB (mi dice nella norma) e in modo non ufficiale dicendomi che probabilmente c'é una incompatibilità tra la "nuova macchina" e Cisco, consigliandomi di aggiornare il software del Cisco al 3.0.14 ( la mia attuale credo sia "FW Version: 2.5.42") od al limite chiedere di modificare il mio profilo sulla macchina Dslam (mi parlava di un I 411 quello attuale).


Allego la programmazione del 877, ed i livelli di segnale pervenuti quando finalmente si "allinea":

#show conf
Using 2750 out of 131072 bytes
!
! Last configuration change at 22:43:33 GMT Fri May 6 2011 by retlawb
! NVRAM config last updated at 22:45:33 GMT Fri May 6 2011 by retlawb
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname C877
!
boot-start-marker
boot-end-marker
!
enable secret 5 xxxxxxx
no aaa new-model
!
resource policy
!
clock timezone GMT 1
clock summer-time GMT recurring
ip cef
ip dhcp smart-relay
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.64.1 192.168.64.220
!
ip dhcp pool interlan
network 192.168.64.0 255.255.255.0
default-router 192.168.64.1
dns-server 208.67.222.222 208.67.220.220
lease 0 12
!
!
!
!
!
username xxxxxx password 0 xxxxxx
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
description Interfaccia ATM0/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
no snmp trap link-status
pvc 8/35
pppoe-client dial-pool-number 1
!
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
ip address 192.168.64.1 255.255.255.0
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1400
no ip mroute-cache
hold-queue 100 out
!
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp header-compression
dialer pool 1
ppp pap sent-username aliceadsl password 0 aliceadsl
!
ip route 0.0.0.0 0.0.0.0 Dialer0
!
no ip http server
no ip http secure-server
ip nat translation timeout 3600
ip nat translation tcp-timeout 3600
ip nat translation udp-timeout 1200
ip nat translation finrst-timeout 300
ip nat translation syn-timeout 120
ip nat translation dns-timeout 300
ip nat translation icmp-timeout 120
ip nat translation max-entries 4096
ip nat inside source list 101 interface Dialer0 overload
ip nat inside source static tcp 192.168.64.71 15123 interface Dialer0 15123
ip nat inside source static udp 192.168.64.71 39137 interface Dialer0 39137
ip nat inside source static tcp 192.168.64.71 46832 interface Dialer0 46832
ip nat inside source static udp 192.168.64.71 46832 interface Dialer0 46832
ip nat inside source static tcp 192.168.64.71 5900 interface Dialer0 5900
!
access-list 1 permit 192.168.64.0 0.0.0.255
access-list 101 permit ip any any
dialer-list 1 protocol ip permit
!
!
!
control-plane
!
!
line con 0
exec-timeout 120 0
login local
no modem enable
stopbits 1
line aux 0
line vty 0 4
exec-timeout 0 0
login local
!
scheduler max-task-time 5000
ntp clock-period 17178796
ntp server 193.204.114.232
!
webvpn context Default_context
ssl authenticate verify all
!
no inservice
!
end

C877#
----------------------------------------------------

C877#show dsl interface atm 0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.5 (ADSL2+) Annex A
ITU STD NUM: 0x03 0x2
Chip Vendor ID: 'STMI' 'IFTN'
Chip Vendor Specific: 0x0000 0x71B8
Chip Vendor Country: 0x0F 0xB5
Modem Vendor ID: 'CSCO' ' '
Modem Vendor Specific: 0x0000 0x0000
Modem Vendor Country: 0xB5 0x00
Serial Number Near: FCZ1111220M
Serial Number Far:
Modem Version Near: 12.4(6)T2
Modem Version Far:
Capacity Used: 71% 100%
Noise Margin: 5.5 dB 24.5 dB
Output Power: 20.5 dBm 10.5 dBm
Attenuation: 41.0 dB 14.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x87
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 7660 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42



Il Noise Margin ATU-R (DS) varia da 5 a 15 dB.

Ringrazio fin da ora e scusatemi per il "gergo" non troppo tecnico.

Ringrazio e saluto

Retlawb

retlawb ha scritto: Modem Version Near: 12.4(6)T2
FW Version: 2.5.42

Beh, direi di passare a 12.4(24)T5 o 15.0(1)M5 come IOS e almeno 4.0.15 come firmware ADSL.

Perdonate la mia ignoranza,
sapevo che un tempo avere il firmware dei Cisco era semplice
oggi non é + così, corretto ?

Dove trovo i firmware (ovviamente non sono iscritto alla Cisco come operatore professionale)

Grazie

Retlawb

Te lo mando io stasera. Mandami in privato la tua email.

Ciao

Buon giorno,
Grazie al Vostro aiuto sono riuscito a risolvere il problema per il Cisco 877.

Purtroppo non sono riuscito a risolvere il problema per il "vecchio" Cisco 827H
credo che sia dovuto ad uno dei seguenti problemi:
IOS datata (Version 12.2(4)YA7)
Firmware DSL incompatibile o con la IOS o con in Cisco 827H.

Nei vari tentativi fatti ho anche cancellato, un po da "pollo", la IOS (c820-k9osy6-mz.122-4.YA7.bin)
Il caso volle che poco prima avevo fatto una copia e tramite comandi ROMMON sono riuscito a ricaricarla in FLAS:

Vi posto ciò che mi dice il 827H.

Ringrazio fin d'ora l'indispensabile aiuto datomi.

Grazie

Retlawb



System Bootstrap, Version 12.2(4r)XM2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2002 by cisco Systems, Inc.
C800/SOHO series (Board ID: 20-62) platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80013000, size: 0x5110ec
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################# [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-K9OSY6-M), Version 12.2(4)YA7, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 09-Oct-03 01:17 by ealyon
Image text-base: 0x80013170, data-base: 0x808F3AA4


Compliance with U.S. Export Laws and Regulations - Encryption

This product performs encryption and is regulated for export
by the U.S. Government.

This product is not authorized for use by persons located
outside the United States and Canada that do not have prior
approval from Cisco Systems, Inc. or the U.S. Government.

This product may not be exported outside the U.S. and Canada
either by physical or electronic means without PRIOR approval
of Cisco Systems, Inc. or the U.S. Government.

Persons outside the U.S. and Canada may not re-export, resell,
or transfer this product by either physical or electronic means
without prior approval of Cisco Systems, Inc. or the U.S.
Government.

CISCO C827H (MPC855T) processor (revision 0x501) with 31744K/1024K bytes of memory.
Processor board ID FOC07070YXL (500008554), with hardware revision 0000
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)

ATM0 :ILMI disabling will take effect in the next interface restart


Press RETURN to get started!


00:00:13: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up
00:00:15: %LINK-3-UPDOWN: Interface ATM0, changed state to down
00:00:16: %DIALER-6-BIND: Interface Vi1 bound to profile Di0
00:00:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
00:00:16: %SYS-5-CONFIG_I: Configured from memory by console
00:00:22: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-K9OSY6-M), Version 12.2(4)YA7, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 09-Oct-03 01:17 by ealyon
00:00:22: %SNMP-5-COLDSTART: SNMP agent on host C_827H is undergoing a cold start
00:00:26: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up

User Access Verification

Username: ********
Password: ********
C_827H>en
Password:********

C_827H#show interfaces atm 0
ATM0 is down, line protocol is down
Hardware is PQUICC_SAR (with Alcatel ADSL Module)
Description: Interfaccia ATM0/0
MTU 1500 bytes, sub MTU 1500, BW 800 Kbit, DLY 80 usec,
reliability 0/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 1024 VCs per VP, 0 current VCCs
VC idle disconnect time: 300 seconds
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/224/0/0 (size/max/drops/flushes); Total output drops: 20
Queueing strategy: None
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out


C_827H#show interfaces dialer 0
Dialer0 is up, line protocol is up (spoofing)
Hardware is Unknown
Description: Interfaccia Dialer0/0
Internet address will be negotiated using DHCP
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
DTR is pulsed for 1 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 00:05:15
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
C_827H#


C_827H#show conf
Using 2382 out of 131072 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname C_827H
!
enable secret 5 $1######
!
username ###### password 7 @@@@@@@@
no ip domain-lookup
ip name-server 208.67.222.222
ip name-server 208.67.220.220
ip dhcp excluded-address 192.168.64.1 192.168.64.220
!
ip dhcp pool LAN
network 192.168.64.0 255.255.255.0
default-router 192.168.64.1
dns-server 208.67.222.222 208.67.220.220
lease 0 12
!
ip ssh time-out 120
ip ssh authentication-retries 3
!
!
!
!
interface Ethernet0
description Interfaccia Ethernet0/0 - Lan interna
ip address 192.168.64.1 255.255.255.0
ip broadcast-address 192.168.64.255
ip nat inside
hold-queue 100 out
!
interface ATM0
description Interfaccia ATM0/0
no ip address
no atm auto-configuration
no atm ilmi-keepalive
no atm address-registration
no atm ilmi-enable
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
bundle-enable
dsl operating-mode ansi-dmt
hold-queue 224 in
!
interface Dialer0
description Interfaccia Dialer0/0
ip address negotiated
ip nat outside
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname aliceadsl
ppp chap password 7 0207085208030E255F42
ppp pap sent-username aliceadsl password 7 1108150C14170A081726
!
ip nat translation timeout 420
ip nat translation tcp-timeout 120
ip nat translation pptp-timeout 420
ip nat translation icmp-timeout 1
ip nat translation max-entries 1000
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source list 101 interface Dialer0 overload
ip nat inside source static tcp 192.168.64.71 5900 interface Dialer0 5900
ip nat inside source static udp 192.168.64.71 46832 interface Dialer0 46832
ip nat inside source static tcp 192.168.64.71 46832 interface Dialer0 46832
ip nat inside source static udp 192.168.64.71 39137 interface Dialer0 39137
ip nat inside source static tcp 192.168.64.71 15123 interface Dialer0 15123
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
ip pim bidir-enable
!
!
access-list 1 permit 192.168.64.0 0.0.0.255
access-list 101 permit ip 192.168.64.0 0.0.0.255 any
dialer-list 1 protocol ip permit
!
line con 0
exec-timeout 120 0
login local
stopbits 1
line vty 0 4
exec-timeout 0 0
login local
!
scheduler max-task-time 5000
end


C_827H#dir flash:
Directory of flash:/

1 -rw- 5313032 <no date> c820-k9osy6-mz.122-4.YA7.bin
2 -rw- 997384 <no date> adsl_alc_20190.bin

8388608 bytes total (2078064 bytes free)


C_827H#show ver
Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-K9OSY6-M), Version 12.2(4)YA7, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 09-Oct-03 01:17 by ealyon
Image text-base: 0x80013170, data-base: 0x808F3AA4

ROM: System Bootstrap, Version 12.2(4r)XM2, RELEASE SOFTWARE (fc1)
ROM: C820 Software (C820-K9OSY6-M), Version 12.2(4)YA7, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)

C_827H uptime is 8 minutes
System returned to ROM by power-on
System image file is "flash:c820-k9osy6-mz.122-4.YA7.bin"

CISCO C827H (MPC855T) processor (revision 0x501) with 31744K/1024K bytes of memory.
Processor board ID FOC07070YXL (500008554), with hardware revision 0000
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)

Configuration register is 0x2102

C_827H#

retlawb ha scritto: C_827H#show ver
Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-K9OSY6-M), Version 12.2(4)YA7, EARLY DEPLOYMENT REL
EASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Thu 09-Oct-03 01:17 by ealyon
Image text-base: 0x80013170, data-base: 0x808F3AA4

ROM: System Bootstrap, Version 12.2(4r)XM2, RELEASE SOFTWARE (fc1)
ROM: C820 Software (C820-K9OSY6-M), Version 12.2(4)YA7, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)

C_827H uptime is 8 minutes
System returned to ROM by power-on
System image file is "flash:c820-k9osy6-mz.122-4.YA7.bin"

CISCO C827H (MPC855T) processor (revision 0x501) with 31744K/1024K bytes of memory.
Processor board ID FOC07070YXL (500008554), with hardware revision 0000
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)

Configuration register is 0x2102

C_827H#

Potresti aggiornarlo:


IP PLUS
c820-sy6-mz.124-25e.bin
Release Date: 18/MAR/2011
Size: 6804.75 KB (6968060 bytes)
Minimum Memory: DRAM:32MB Flash:8MB

o

IP/FW
c820-oy6-mz.124-25e.bin
Release Date: 18/MAR/2011
Size: 5705.88 KB (5842820 bytes)
Minimum Memory: DRAM:32MB Flash:8MB

e forse anche

C820_RM_ALT.srec.122-4r.XM4
Release Date: 06/OCT/2008
C828 ROMMON Upgrade; for No Service Pass
Size: 434.11 KB (444519 bytes)

ma mi sa di no: lo vedo per l'827, non per l'827 H

per l'ADSL non so. prova col firmware incorporato nell'IOS per adesso.

Purtroppo uno dei miei tanti problemi é reperire i files.

Altro dubbio:
Il Cisco 827H é un router soho "datato" avente 4 porte ethernet 10baseT.

Il mio problema sorge, credo, perché Telecom mi ha "collegato" su un nuovo Dslam (mi dicono made in Cina).
Se non ho capito male, configura la porta verso di me come ADSL2+ bloccata a 7 Mbit.

Essendo il 827H lato Ethernet 10BaseT, ha senso colegarsi su una ADSL2+
(se non erro dovrebbe andare fino a 20 Mbit)?

Grazie per la pazienza

Retlawb

retlawb ha scritto:Purtroppo uno dei miei tanti problemi é reperire i files.

Altro dubbio:
Il Cisco 827H é un router soho "datato" avente 4 porte ethernet 10baseT.

Il mio problema sorge, credo, perché Telecom mi ha "collegato" su un nuovo Dslam (mi dicono made in Cina).
Se non ho capito male, configura la porta verso di me come ADSL2+ bloccata a 7 Mbit.

Essendo il 827H lato Ethernet 10BaseT, ha senso colegarsi su una ADSL2+
(se non erro dovrebbe andare fino a 20 Mbit)?

Grazie per la pazienza

Retlawb

L'837 non puo' fare ADSL2+. E' per questo che sono passato all'877. L'827H non lo so.

8Mbit _massacrava_ il mio 837.