Configurazione Router CISCO 2801

[BARONE85]

Reload in 15
Non salvare se ti chiede se lo vuoi fare

Conf t
Int atm 0/1/0.w
No zone-member security out-zone

System configuration has been modified. Save? [yes/no]: n
Reload scheduled for 15:13:18 PCTime Fri Jun 17 2011 (in 15 minutes) by ferraris
on vty0 (10.0.0.113)
Reload reason: Reload Command
Proceed with reload? [confirm]
brofind#reload in 15

System configuration has been modified. Save? [yes/no]: n
Reload scheduled for 15:13:33 PCTime Fri Jun 17 2011 (in 15 minutes) by ferraris
on vty0 (10.0.0.113)
Reload reason: Reload Command
Proceed with reload? [confirm]c
brofind#conf t
Enter configuration commands, one per line. End with CNTL/Z.
brofind(config)#int atm 0/1/0.w
^
% Invalid input detected at '^' marker.

brofind(config)#

Int fa0/0
No zone-member security iin-zone

#no zone-member security iin-zone
% Security zone name iin-zone not defined



Se puoi ancora parlare col router
Reload cancel

reload cancel
***#


***
*** --- SHUTDOWN ABORTED ---
***

[BARONE85]

Se togli 103 cosa succede?

Se devo digitare tutto su questo blackberry:

Conf t
Int atm0/1/0.1 point-to-point
No ip access-group 103 in

Enter configuration commands, one per line. End with CNTL/Z.
***(config)#int atm0/1/0.1 point-to-point
***(config-subif)#no ip access-group 103 in
***(config-subif)#^Z
***#
Ti torna?provo a dare gateway 160 e fare una connessione?

Vediamo

Show start non dice quando la config e' stata salvata?

Using 16897 out of 196600 bytes
!
! Last configuration change at 12:30:30 PCTime Tue Jun 7 2011 by ferraris
! NVRAM config last updated at 12:30:36 PCTime Tue Jun 7 2011 by ferraris
!

[ghira]

Per favore mostraci a sezione line vty 0 4 da sh run

Devi limitare l'accesso a router

E se puoi vivere senza per ora

Conf t
No ip http server
No ip http secure-server

Uccidendo l'interfaccia grafica

[ghira]

Reload in 15
Non salvare se ti chiede se lo vuoi fare

Conf t
Int atm 0/1/0.w
No zone-member security out-zone

System configuration has been modified. Save? [yes/no]: n
Reload scheduled for 15:13:18 PCTime Fri Jun 17 2011 (in 15 minutes) by ferraris
on vty0 (10.0.0.113)
Reload reason: Reload Command
Proceed with reload? [confirm]
brofind#reload in 15

System configuration has been modified. Save? [yes/no]: n
Reload scheduled for 15:13:33 PCTime Fri Jun 17 2011 (in 15 minutes) by ferraris
on vty0 (10.0.0.113)
Reload reason: Reload Command
Proceed with reload? [confirm]c
brofind#conf t
Enter configuration commands, one per line. End with CNTL/Z.
brofind(config)#int atm 0/1/0.w
^
% Invalid input detected at '^' marker.

brofind(config)#

Int fa0/0
No zone-member security iin-zone

#no zone-member security iin-zone
% Security zone name iin-zone not defined



Se puoi ancora parlare col router
Reload cancel

reload cancel
***#


***
*** --- SHUTDOWN ABORTED ---
***

In-zone, come nella config

[paolomat75]

@paolo:

sh ip cef exact-route 10.0.0.160 8.8.8.8
10.0.0.160 -> 8.8.8.8 : ATM0/1/0.1 (attached)
brofind#traceroute 8.8.8.8 source 89.118.201.50

Type escape sequence to abort.
Tracing the route to google-public-dns-a.google.com (8.8.8.

1 * * *
2 * * *
3 * * *
....

A questo punto

Codice: Seleziona tutto

sh ip cef exact-route 89.118.201.50 8.8.8.8
sh ip cef exact-route 89.118.201.50 89.118.201.50
traceroute 89.118.201.49

Oltre naturalmente alle modifiche che ha detto ghira.
Voglio vedere se ne usciamo fuori....

Posta i comandi sopra

[ghira]

Reload in 15
Non salvare se ti chiede se lo vuoi fare

Conf t
Int atm 0/1/0.w
No zone-member security out-zone

System configuration has been modified. Save? [yes/no]: n
Reload scheduled for 15:13:18 PCTime Fri Jun 17 2011 (in 15 minutes) by ferraris
on vty0 (10.0.0.113)
Reload reason: Reload Command
Proceed with reload? [confirm]
brofind#reload in 15

System configuration has been modified. Save? [yes/no]: n
Reload scheduled for 15:13:33 PCTime Fri Jun 17 2011 (in 15 minutes) by ferraris
on vty0 (10.0.0.113)
Reload reason: Reload Command
Proceed with reload? [confirm]c
brofind#conf t
Enter configuration commands, one per line. End with CNTL/Z.
brofind(config)#int atm 0/1/0.w
^
% Invalid input detected at '^' marker.

brofind(config)#

Int fa0/0
No zone-member security iin-zone

#no zone-member security iin-zone
% Security zone name iin-zone not defined



Se puoi ancora parlare col router
Reload cancel

reload cancel
***#



***
**
* --- SHUTDOWN ABORTED ---
***

In-zone, come nella config

E atm0/1/0.1 come nella config
Stampane una copia sto usandoi un blackberry e digityare e u. Cvasinoi

[BARONE85]

conf t
Enter configuration commands, one per line. End with CNTL/Z.
brofind(config)#no ip http server
brofind(config)#no ip http secure-server
brofind(config)#int fat 0/0
^
% Invalid input detected at '^' marker.

brofind(config)#Int fa0/0
brofind(config-if)#no zone-member security in-zone
brofind(config-if)#^Z
brofind#

brofind(config)#int atm0/1/0.1
brofind(config-subif)#no zone-member security out-zone

Ok fatto tutto, ora?

[ghira]

Cosa e' statop cambviayo iul 7?

[ghira]

conf t
Enter configuration commands, one per line. End with CNTL/Z.
brofind(config)#no ip http server
brofind(config)#no ip http secure-server
brofind(config)#int fat 0/0
^
% Invalid input detected at '^' marker.

brofind(config)#Int fa0/0
brofind(config-if)#no zone-member security in-zone
brofind(config-if)#^Z
brofind#

brofind(config)#int atm0/1/0.1
brofind(config-subif)#no zone-member security out-zone

Ok fatto tutto, ora?

Se pinghi e tracerouti dal router e da pc cosa succede adesso?

[BARONE85]

Funziona in parte...alcuni siti accedo e altri no!!!
Ghira hai pm...

[ghira]

Ancora niente? In tal cvso

Prova

Conf t
No ip route 0.0.0.0 0.0.0.0 atm 0/1/0.1
Ip route 0.0.0.0 0.0.0.0 89.118.201.49

Temporaneamente

[paolomat75]

Bene. Non capisco comunque cosa sia successo, se prima funzionava.

[ghira]

Funziona in parte...alcuni siti accedo e altri no!!!
Ghira hai pm...

Devi devi devi proteggere line vty 0 4 adesso!

[BARONE85]

Non vedo la sezione "line vty 0 4" nella configurazione

C'e' un comando access-class?

E ripeto: show log cosa dice?

Non riesco a capire dal tuo post.

[ghira]

Non vedo la sezione "line vty 0 4" nella configurazione

C'e' un comando access-class?

E ripeto: show log cosa dice?

Non riesco a capire dal tuo post.

Verso la fine di "show run" c'e' una sezione
Line vty 0 4

Dicci cosa contiene