Cisco 827-4v funzionante Ser-Asterisk; ok call-in/call-out

[Pimbolix]

A chi potesse servire... dopo tante prove e test e diverse peripezie, ho completato una conf funzionante in tutto, testata su sistemi Ser-Asterisk funziona egregiamente.
La versione IOS che ho usato e la 12.4 (3) ovvero c820-ov6y6-mz-124-3.bin

questa di seguito e la configurazione a 4 linee diversificate, completate ovviamente i campi con i dati forniti dal vostro fornitore, ip, dns, sip srv ecc.

Ciao a tutti e spero di essere stato utile.... alla prox.

!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Cisco_SIP
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
no ip dhcp use vrf connected
!
ip dhcp pool SERVER
import all
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server x.x.x.x
!
!
ip name-server x.x.x.x
!
!
voice call send-alert
voice call disc-pi-off
voice call debug short-header
voice rtp send-recv
voice dsp release early
!
!
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
!
!
!
!
!
!
!
!
voice translation-rule 1
rule 1 /^0/ /9990/
rule 2 /^1/ /9991/
rule 3 /^3/ /9993/
rule 8 /^8/ /9998/
rule 9 reject /.*/
!
!
!
!
!
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
hold-queue 100 out
!
interface ATM0
no ip address
no ip mroute-cache
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
ip address x.x.x.x 255.255.255.0
ip nat outside
ip virtual-reassembly
no ip mroute-cache
pvc 0/32
encapsulation aal5snap
!
!
ip classless
ip route 0.0.0.0 0.0.0.0 ATM0.1
no ip http server
!
ip nat inside source list 1 interface ATM0.1 overload
access-list 1 permit 192.168.1.0 0.0.0.255
!
route-map Data permit 10
match interface Ethernet0
set ip precedence priority
!
!
control-plane
!
!
voice-port 1
ring cadence pattern01
echo-cancel coverage 32
no vad
cptone IT
timeouts interdigit 5
bearer-cap Speech
caller-id enable
!
voice-port 2
ring cadence pattern01
cptone IT
!
voice-port 3
ring cadence pattern01
cptone IT
!
voice-port 4
ring cadence pattern01
cptone IT
!
dial-peer voice 1 voip
translation-profile outgoing calling-outbound
destination-pattern [0,1,3,8]T
progress_ind setup enable 3
voice-class codec 1
session protocol sipv2
session target sip-server
session transport udp
dtmf-relay sip-notify
fax rate 14400
fax protocol pass-through g711alaw
ip qos dscp cs5 media
no vad
!
dial-peer voice 2 pots
destination-pattern 111111
port 4
authentication username 111111 password xxxxxx
!
dial-peer voice 3 pots
preference 2
destination-pattern 222222
port 3
authentication username 222222 password xxxxxx
!
dial-peer voice 4 pots
preference 3
destination-pattern 333333
port 2
authentication username 333333 password xxxxxx
!
dial-peer voice 5 pots
preference 4
destination-pattern 444444
port 1
authentication username 444444 password xxxxxx
!
gateway
timer receive-rtp 1200
!
sip-ua
retry invite 4
retry response 3
retry bye 2
retry cancel 2
retry register 10
registrar dns:sip.server.it:5060 expires 60
sip-server dns:sip.server.it:5060
!
!
line con 0
line vty 0 4
login
!
scheduler max-task-time 5000
end

[Pimbolix]

ovviamente funziona anche il fax....

[TheIrish]

Grazie mille. Sarà sicuramente utilissimo a molti