dial-peer
Inviato: gio 30 ott , 2008 6:25 pm
Vorrei una mano da tutti voi
non riesco a far funzionare il dial peer passa da primo al secondo ed attende 30 secondi per poi tornare su se stesso senza switchare sul secondo.
incollo la configurazione attuale:
---------------------------
dial-peer voice 20001 voip
description Call Manager Phone
preference 1
destination-pattern 2....
voice-class codec 1
session protocol sipv2
session target ipv4:10.233.233.233
session transport udp
dtmf-relay rtp-nte
no vad
!
dial-peer voice 20002 voip
description Call Manager Phones
huntstop
preference 2
destination-pattern 2....
voice-class codec 1
session protocol sipv2
session target ipv4:10.232.117.204
session transport udp
dtmf-relay rtp-nte
no vad
!
!
gateway
timer receive-rtp 1200
!
sip-ua
set pstn-cause 6 sip-status 503
set pstn-cause 18 sip-status 408
set pstn-cause 27 sip-status 502
set pstn-cause 31 sip-status 480
set pstn-cause 44 sip-status 503
set pstn-cause 58 sip-status 503
set pstn-cause 88 sip-status 503
set pstn-cause 95 sip-status 503
set pstn-cause 102 sip-status 504
set pstn-cause 111 sip-status 500
retry invite 1
retry response 3
retry bye 3
retry cancel 3
timers trying 1000
timers keepalive down 5
timers options 100
!
!
line con 0
login local
line aux 0
line vty 0 4
access-class 23 in
exec-timeout 0 0
privilege level 15
login local
transport input telnet
line vty 5 15
access-class 23 in
privilege level 15
login local
transport input telnet
!
scheduler allocate 20000 1000
ntp logging
ntp clock-period 17177710
ntp server 10.232.117.204
!
end
-----------------------
La versione รจ questa:
---------------------------
Cisco IOS Software, 3800 Software (C3845-IPVOICE-M), Version 12.4(15)T3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 25-Jan-08 00:11 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
vgsvilaldo uptime is 1 week, 3 days, 1 hour, 5 minutes
System returned to ROM by power-on
System image file is "flash:c3845-ipvoice-mz.124-15.T3.bin"
Cisco 3845 (revision 1.0) with 225280K/36864K bytes of memory.
Processor board ID FHK1212F4M3
2 Gigabit Ethernet interfaces
31 Serial interfaces
2 Channelized E1/PRI ports
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
250880K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
---------------------------
Attendo un vostro responso unrgente
GRAZIE a tutti
non riesco a far funzionare il dial peer passa da primo al secondo ed attende 30 secondi per poi tornare su se stesso senza switchare sul secondo.
incollo la configurazione attuale:
---------------------------
dial-peer voice 20001 voip
description Call Manager Phone
preference 1
destination-pattern 2....
voice-class codec 1
session protocol sipv2
session target ipv4:10.233.233.233
session transport udp
dtmf-relay rtp-nte
no vad
!
dial-peer voice 20002 voip
description Call Manager Phones
huntstop
preference 2
destination-pattern 2....
voice-class codec 1
session protocol sipv2
session target ipv4:10.232.117.204
session transport udp
dtmf-relay rtp-nte
no vad
!
!
gateway
timer receive-rtp 1200
!
sip-ua
set pstn-cause 6 sip-status 503
set pstn-cause 18 sip-status 408
set pstn-cause 27 sip-status 502
set pstn-cause 31 sip-status 480
set pstn-cause 44 sip-status 503
set pstn-cause 58 sip-status 503
set pstn-cause 88 sip-status 503
set pstn-cause 95 sip-status 503
set pstn-cause 102 sip-status 504
set pstn-cause 111 sip-status 500
retry invite 1
retry response 3
retry bye 3
retry cancel 3
timers trying 1000
timers keepalive down 5
timers options 100
!
!
line con 0
login local
line aux 0
line vty 0 4
access-class 23 in
exec-timeout 0 0
privilege level 15
login local
transport input telnet
line vty 5 15
access-class 23 in
privilege level 15
login local
transport input telnet
!
scheduler allocate 20000 1000
ntp logging
ntp clock-period 17177710
ntp server 10.232.117.204
!
end
-----------------------
La versione รจ questa:
---------------------------
Cisco IOS Software, 3800 Software (C3845-IPVOICE-M), Version 12.4(15)T3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Fri 25-Jan-08 00:11 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
vgsvilaldo uptime is 1 week, 3 days, 1 hour, 5 minutes
System returned to ROM by power-on
System image file is "flash:c3845-ipvoice-mz.124-15.T3.bin"
Cisco 3845 (revision 1.0) with 225280K/36864K bytes of memory.
Processor board ID FHK1212F4M3
2 Gigabit Ethernet interfaces
31 Serial interfaces
2 Channelized E1/PRI ports
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
250880K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
---------------------------
Attendo un vostro responso unrgente
GRAZIE a tutti