cisco 827 password recovery

[sahachiel]

Salve
ho fatto tutta la procedura per il recupero della password e sembra andare tutto ok, pero' al riavvio del router, appena finisce tutto il controllo mi chiede USERNAME:

ma io ho resettato la password, l'username non lo conosco...non c'e' un modo per portarlo a factory default magary da rommon?

Grazie mille

[Wizard]

Che procedura hai utilizzato?

[Helix]

sembra come che il password recovery non abbia funzionato...la cosa migliore è dire effettivamente che procedura hai usato

[sahachiel]

la procedura e' quella descritta sul sito:

break appena acceso

confreg 0x2142

reset

no

enable

configure memory

configure terminal

enable secret <password>

config-register 0x2102

Ctrl-z

write memory


tutto qui, ne piu' ne meno...aiuto please..

[sahachiel]

al riavvio mi dice questo:

System Bootstrap, Version 12.1(1r)XB1, RELEASE SOFTWARE (fc1)
Copyright (c) 2000 by cisco Systems, Inc.
C827 platform with 24576 Kbytes of main memory

program load complete, entry point: 0x80013000, size: 0x3c93dc
Self decompressing the image :
(accorcio senno' prende 2 pagine di cancelletti
####################[OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-Y6-M), Version 12.2(4)YA4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 27-Dec-02 11:43 by ealyon
Image text-base: 0x80013170, data-base: 0x8067CBD0

CISCO C827 (MPC855T) processor (revision 0x701) with 23552K/1024K bytes of memory.
Processor board ID JAD06090QVV (2320453514), with hardware revision 0000
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)


ê


Press RETURN to get started!


00:00:09: %LINK-5-CHANGED: Interface Ethernet0, changed state to administratively down
00:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
00:00:10: %SYS-5-CONFIG_I: Configured from memory by console
00:00:10: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down
00:00:12: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
00:00:14: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS

User Access Verification

Username: (tm) C820 Software (C820-Y6-M), Version 12.2(4)YA4, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(5.4)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 27-Dec-02 11:43 by ealyon
00:00:14: %SNMP-5-COLDSTART: SNMP agent on host ASI is undergoing a cold start
Username:

[sahachiel]

risolto

dopo enable ho fatto conf t

e poi config-register 0x2102

Grazie a tutti di cuore