CiscoForums.it

Salve a tutti
stasera ho provato a mettere il CRWS sul mio 827

Di seguito posto la mia configurazione prima di aver messo il CRWS Crws-v33Bn28...in quanto dopo ho dovuro ripristinare tutto


Cisco827#s ver
Cisco Internetwork Operating System Software
IOS (tm) C820 Software (C820-Y6-M), Version 12.2(2)XK3, EARLY DEPLOYMENT
RELEASE SOFTWARE (fc1)
Synched to technology version 12.2(2.5)T
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 10-May-02 18:28 by philuu
Image text-base: 0x80013170, data-base: 0x806429A4

ROM: System Bootstrap, Version 12.2(4r)XM2, RELEASE SOFTWARE (fc1)
ROM: C820 Software (C820-Y6-M), Version 12.2(2)XK3, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)

Cisco827 uptime is 12 hours, 41 minutes
System returned to ROM by reload at 23:11:27 CET Tue Jan 1 2008
System restarted at 23:12:32 CET Tue Jan 1 2008
System image file is "flash:c820-y6-mz.122-2.XK3.bin"

CISCO C827 (MPC855T) processor (revision 0x501) with 15360K/1024K bytes of
memory.
Processor board ID JAD04460FWG (3605286623), with hardware revision 0000
CPU rev number 5
Bridging software.
1 Ethernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
128K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
2048K bytes of processor board Web flash (Read/Write)

Configuration register is 0x2102



Cisco827#show configuration
Using 1647 out of 131072 bytes
!
! Last configuration change at 11:05:17 CET Wed Jan 2 2008
! NVRAM config last updated at 11:05:18 CET Wed Jan 2 2008
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Cisco827
!
enable secret XXXXXXX
enable password XXXXX
!
clock timezone CET 1
clock summer-time CET recurring
ip subnet-zero
ip host-routing
!
!
!
!
interface Ethernet0
ip address 192.168.XXX.XXX 255.255.255.0
ip nat inside
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
dsl operating-mode auto
hold-queue 224 in
!
interface Dialer0
ip address negotiated
no ip proxy-arp
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
pulse-time 0
ppp authentication pap callin
ppp pap sent-username XXXXXXXXX password XXXXXXXXXXXX
!
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static udp 192.168.XXX.XXX6257 interface Dialer0 6257
ip nat inside source static tcp 192.168.XXX.XXX 6699 interface Dialer0 6699
ip nat inside source static tcp 192.168.XXX.XXX 80 interface Dialer0 80
ip nat inside source static udp 192.168.XXX.XXX 4676 interface Dialer0 4676
ip nat inside source static tcp 192.168.XXX.XXX 4666 interface Dialer0 4666
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
access-list 100 permit ip any any
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
line con 0
stopbits 1
line vty 0 4
password XXXXX
login
!
scheduler max-task-time 5000
sntp server 193.204.114.232
end

Morale della favola...quando cerco di raggiungerlo tramite http...non riesce a caricarmi la pagina...cosa può essere?

Beh, finchè c'è il comando "no ip http server " fa un po' fatica ad andare...

Wizard ha scritto:Beh, finchè c'è il comando "no ip http server " fa un po' fatica ad andare...

Codice: Seleziona tutto

ip http server 

grazie mille...
ora mi chiede login e pw...da telnet non mi è mai stata chiesta la login...come la imposto?!?

però, quando carico il CRWS, cmq gli passo anche il file di configurazione che ha ip http server...e cmq si blocca