Vecchio 1760 con password recovery disabilitata: no reset
Inviato: mar 03 dic , 2013 5:05 pm
Ciao
Posseggo un vecchio 1760 con la funzionalita' di password recovery disabilitata
Poco male, a me serve un factory default come ho fatto molte volte .
Con questo pero' non mi riesce, il boot e' sempre con la config. originale....
Procedo cosi:
Boot normale :
Self decompressing the image : #################################################
################################################################################
################################################################ [OK]
Smart Init is disabled. IOMEM set to: 15
PMem allocated: 57042944 bytes; IOMem allocated: 10065920 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y7-M), Version 12.3(6d), RELEASE SOFTWARE (fc1
)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 15-Oct-04 03:46 by kellythw
Image text-base: 0x80008120, data-base: 0x81440804
Invio il BREAK in questo punto e il router mi risponde :
Do you want to reset the router to factory default
configuration and proceed [y/n] ? y
Reset router configuration to factory default.
cisco 1760 (MPC860P) processor (revision 0x500) with 55706K/9830K bytes of memor
y.
Processor board ID FOC07450X9P (3881152211), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
WARNING:
Executing this command will disable password recovery mechanism.
Do not execute this command without another plan for
password recovery.
Are you sure you want to continue? [yes/no]: y
A questo punto il router pero' continua il boot con la configurazione originale , con la sua password sconosciuta e il recovery ancora disabilitato.
Ho fatto piu' volte questa procedura, con Wic installate e non , togliendo PVDM e ram
Nulla da fare
Qualche suggerimento ????
Grazie
Posseggo un vecchio 1760 con la funzionalita' di password recovery disabilitata
Poco male, a me serve un factory default come ho fatto molte volte .
Con questo pero' non mi riesce, il boot e' sempre con la config. originale....
Procedo cosi:
Boot normale :
Self decompressing the image : #################################################
################################################################################
################################################################ [OK]
Smart Init is disabled. IOMEM set to: 15
PMem allocated: 57042944 bytes; IOMem allocated: 10065920 bytes
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV8Y7-M), Version 12.3(6d), RELEASE SOFTWARE (fc1
)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 15-Oct-04 03:46 by kellythw
Image text-base: 0x80008120, data-base: 0x81440804
Invio il BREAK in questo punto e il router mi risponde :
Do you want to reset the router to factory default
configuration and proceed [y/n] ? y
Reset router configuration to factory default.
cisco 1760 (MPC860P) processor (revision 0x500) with 55706K/9830K bytes of memor
y.
Processor board ID FOC07450X9P (3881152211), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)
WARNING:
Executing this command will disable password recovery mechanism.
Do not execute this command without another plan for
password recovery.
Are you sure you want to continue? [yes/no]: y
A questo punto il router pero' continua il boot con la configurazione originale , con la sua password sconosciuta e il recovery ancora disabilitato.
Ho fatto piu' volte questa procedura, con Wic installate e non , togliendo PVDM e ram
Nulla da fare
Qualche suggerimento ????
Grazie