Problema Configurazione Router Cisco 2600 HDSL Telecom

[crashboy]

Salve ragazzi‚ sentite io ho un problema come si può vedere dal topic smile mi hanno portato l'HDSL ma non riesco a configurare il Router Cisco 2600 per farla funzionare‚ i dati che mi hanno dato sono :

INDIRIZZI IP ASSEGNATI : 88.41.138.160 NETWORK MASK 255.255.255.240
DEFAULT GATEWAY 88.41.138.161
PUNTO PUNTO 88.41.87.158 SUBNET MASK 255.255.255.252
DLCI 130

Ed ecco la mia configurazione‚ per quanto sia sbagliata ve la posto lo stesso :


Building configuration…

Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password–encryption
!
hostname Router
!
enable secret
enable password mia pass
!
!
!
!
!
ip subnet–zero
no ip source–route
no ip routing
ip domain–name interbusiness.it
ip name–server 151.99.125.2
ip name–server 151.99.125.3
!
!
!
!
interface Ethernet0/0
ip address 88.41.138.161 255.255.255.240
ip access–group inside in
no ip redirects
no ip unreachables
no ip directed–broadcast
no ip proxy–arp
no ip route–cache
no ip mroute–cache
full–duplex
no cdp enable
!
interface Serial0/0
bandwidth 1536
no ip address
no ip directed–broadcast
no ip proxy–arp
encapsulation frame–relay IETF
no ip route–cache
no ip mroute–cache
no fair–queue
frame–relay lmi–type ansi
!
interface Serial0/0.1 point–to–point
description PVC verso interbusiness
bandwidth 1536
ip address 88.41.87.158 255.255.255.252
no ip redirects
no ip unreachables
no ip directed–broadcast
no ip proxy–arp
no ip route–cache
no ip mroute–cache
no arp frame–relay
no cdp enable
frame–relay interface–dlci 130 IETF
!
interface Serial0/1
no ip address
no ip directed–broadcast
no ip route–cache
no ip mroute–cache
!
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/0.1
no ip http server
!
!
line con 0
transport input none
line aux 0
line vty 0 4
password mia pass
login
!
end

Vi ringrazio in anticipo per eventuali risposte·

Ciao a tutti

[crashboy]

Grazie tante per la risposta, ma ancora non funziona. Posto la mia configurazione attuale, dopo le modifiche che mi hai chiesto di fare:

Grazie tante comunque

Building configuration...

Current configuration:
!
version 12.0
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
enable secret
enable password mia pass
!
!
!
!
!
ip subnet-zero
no ip source-route
no ip routing
ip domain-name interbusiness.it
ip name-server 151.99.125.2
ip name-server 151.99.125.3
!
!
!
!
interface Ethernet0/0
ip address 88.41.138.161 255.255.255.240
no ip redirects
no ip unreachables
no ip directed-broadcast
no ip proxy-arp
no ip route-cache
no ip mroute-cache
full-duplex
no cdp enable
!
interface Serial0/0
bandwidth 1536
no ip address
no ip directed-broadcast
no ip proxy-arp
encapsulation frame-relay IETF
no ip route-cache
no ip mroute-cache
no fair-queue
frame-relay lmi-type ansi
!
interface Serial0/0.1 point-to-point
description PVC verso interbusiness
bandwidth 1536
ip unnumbered Ethernet0/0
no ip redirects
no ip unreachables
no ip directed-broadcast
no ip proxy-arp
no ip route-cache
no ip mroute-cache
no arp frame-relay
no cdp enable
frame-relay interface-dlci 130 IETF
!
interface Serial0/1
no ip address
no ip directed-broadcast
no ip route-cache
no ip mroute-cache
shutdown
!
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/0.1
no ip http server
!
!
line con 0
transport input none
line aux 0
line vty 0 4
password mia pass
login
!
end

[crashboy]

Grazie ancora per la disponibilità. Ho provato a cacciare la stringa che mi hai detto e ancora nulla.

Sullo switch ci siamo solo il mio notebook e il router, il mio notebook ha indirizzo 88.41.138.162 il successivo al router. Comunque per testare l'HDSL faccio direttamente un ping dal router.

Attento notizie.

Grazie ancora

[crashboy]

Scusa la domanda stupida forse, ma è possibile che non riesca nemmeno a pingare l'indirizzo punto punto ?

[crashboy]

Ethernet0/0 is up, line protocol is up
Hardware is AmdP2, address is 0004.9a45.a4e0 (bia 0004.9a45.a4e0)
Internet address is 88.41.138.161/28
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
189 packets input, 11472 bytes, 0 no buffer
Received 3 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
191 packets output, 17112 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Serial0/0 is up, line protocol is up
Hardware is PowerQUICC Serial
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF, loopback not set
Keepalive set (10 sec)
LMI enq sent 28, LMI stat recvd 28, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 0 LMI type is ANSI Annex D frame relay DTE
Broadcast queue 0/64, broadcasts sent/dropped 19/0, interface broadcasts 19
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of "show interface" counters 00:04:51
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
43 packets input, 1222 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
3 input errors, 0 CRC, 3 frame, 0 overrun, 0 ignored, 0 abort
48 packets output, 3050 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up

Serial0/0.1 is up, line protocol is up
Hardware is PowerQUICC Serial
Description: PVC verso interbusiness
Internet address is 88.41.87.158/30
MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY IETF
Serial0/1 is administratively down, line protocol is down
Hardware is PowerQUICC Serial
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
Keepalive set (10 sec)
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=down DSR=down DTR=down RTS=down CTS=down

[crashboy]

Preciso che dal client la punto punto riesco a pingarla, e con il ping del router e non riesco ad effettuare nessun ping.

Forse questo dato può esserti utile.

Thanks

[Spark]

Allora: io non so nulla di HDSL, ma...
sei sicuro che il

no ip routing

Debba esserci? Da quel che sapevo io trasformava il tuo router in un bridge...

[crashboy]

Guarda non so.
Forse in questo forum qualcuno potrebbe saperlo, ma io propio no

[crashboy]

Ho chiamato alla Telecom e mi dicono che è tutto apposto, quindi presumono che sia un problema di configurazione.

Qualcuno può darmi una mano cortesemente ?

Grazie

[TheIrish]

Rieccomi. ip routing deve essere abilitato!

E per fortuna

[aghibear]

ciao a tutti,
guardando la configurazione di crashboy,vedo che per la connessione punto-punto utilizza la subinterface di s0.
perche non utilizza l'interfaccia s0?

grazie 1000 a tutti

aghibear