Pagina 1 di 2
Cisco 837 & Tiscali
Inviato: mar 29 ago , 2006 12:07 pm
da CJ
Hi
Firstly I must apologise that I don't speak Italian
I'm based in Ireland, we have an office in Milano and I am trying to remotely configure a Cisco 837 to operate with Tiscali ADSL. I have referred
this guide on Tiscalis website (note this is fior a Cisco 827, the config should be similar) buit I am unable to get the connection to work. The ATM interface picks up the line but the dialer will not work. See samples from config below - I would appreciete if someone could take a look to see if there are any errors:
Codice: Seleziona tutto
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Italy-backup
!
boot-start-marker
boot-end-marker
!
enable secret 5 <password>
enable password 7 <password>
!
no aaa new-model
!
resource policy
!
ip subnet-zero
!
!
no ip dhcp use vrf connected
!
!
ip cef
ip domain name <domain>
ip name-server <dns server>
no ip ips deny-action ips-interface
!
no ftp-server write-enable
!
!
interface Ethernet0
ip address <LAN IP address> 255.255.252.0
ip nat inside
ip virtual-reassembly
no cdp enable
hold-queue 100 out
!
interface Ethernet2
no ip address
shutdown
hold-queue 100 out
!
interface ATM0
no ip address
no ip mroute-cache
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface FastEthernet1
no ip address
duplex auto
speed auto
!
interface FastEthernet2
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet3
no ip address
shutdown
duplex auto
speed auto
!
interface FastEthernet4
no ip address
shutdown
duplex auto
speed auto
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname [email protected]
ppp chap password 7 <password>
ppp pap sent-username [email protected] password 7 <password>
!
!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
!
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Dialer1 overload
!
access-list 1 permit <LAN segment>
dialer-list 1 protocol ip permit
no cdp run
!
!
control-plane
!
!
line con 0
exec-timeout 0 0
no modem enable
stopbits 1
line aux 0
line vty 0 4
exec-timeout 120 0
password 7 <password>
login
!
scheduler max-task-time 5000
end
Codice: Seleziona tutto
sh int di1
Dialer1 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address will be negotiated using IPCP
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi2
Last input never, output never, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Bound to:
Virtual-Access2 is up, [b]line protocol is down[/b]
Hardware is Virtual Access interface
MTU 1500 bytes, BW 0 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP REQsent
PPPoATM vaccess, cloned from Dialer1
Vaccess status 0x44
Bound to ATM0 VCD: 1, VPI: 8, VCI: 35, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Interface is bound to Di1 (Encapsulation PPP)
Last input never, output never, output hang never
Last clearing of "show interface" counters 3w5d
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
447739 packets output, 5372868 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
I plan to use VPN on this link, I am using a basic config at the moment until I can get the line working.
Any assistance appreciated.
CJ
Inviato: mar 29 ago , 2006 1:35 pm
da TheIrish
The configuration seems good enough to make the thing work... but it's not.
Virtual Access 2 line procol is down, this means there's not tunnel working. While we try to find a good reason for this, you should try to debug authentication and encapsulation.
Inviato: gio 07 set , 2006 10:40 am
da CJ
Thanks TheIrish. Did some debugging but theres not a whole lot of useful information coming back (unless I've missed something):
*Apr 12 16:00:14.635: corvil trace: "536312 cdkContext_TraceControl() return 0"
*Apr 12 16:00:15.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:15.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:15.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:15.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:15.307: CEF: background resolution thread state:
*Apr 12 16:00:15.307: Thread fast_thread: Empty
*Apr 12 16:00:15.307: Thread todothread: Empty
*Apr 12 16:00:15.311: Thread slow_thread: Empty
*Apr 12 16:00:16.311: CEF: background resolution thread state:
*Apr 12 16:00:16.311: Thread fast_thread: Empty
*Apr 12 16:00:16.311: Thread todothread: Empty
*Apr 12 16:00:16.311: Thread slow_thread: Empty
*Apr 12 16:00:17.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:17.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:17.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:17.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:17.311: CEF: background resolution thread state:
*Apr 12 16:00:17.311: Thread fast_thread: Empty
*Apr 12 16:00:17.311: Thread todothread: Empty
*Apr 12 16:00:17.311: Thread slow_thread: Empty
*Apr 12 16:00:17.975: Vi2 LCP: TIMEout: State Listen
*Apr 12 16:00:17.975: Vi2 PPP: Authorization required
*Apr 12 16:00:17.975: Vi2 PPP: No remote authentication for call-out
*Apr 12 16:00:17.975: Vi2 AAA/AUTHOR/LCP: Authorization succeeds trivially
*Apr 12 16:00:17.975: Vi2 LCP: O CONFREQ [Listen] id 51 len 10
*Apr 12 16:00:17.975: Vi2 LCP: MagicNumber 0x164E89B9 (0x0506164E89B9)
*Apr 12 16:00:17.979:
*Apr 12 16:00:17.979: c820_vc_tx_start: idb = 0x82034CBC, cos_queue = 0x827C2DC8
*Apr 12 16:00:17.979: c820_aal_send: pak = 0x82345C50, vc = 1, q = 0
*Apr 12 16:00:17.979: pquicc_sar_safe_start: vc = 1
*Apr 12 16:00:18.311: CEF: background resolution thread state:
*Apr 12 16:00:18.311: Thread fast_thread: Empty
*Apr 12 16:00:18.311: Thread todothread: Empty
*Apr 12 16:00:18.311: Thread slow_thread: Empty
*Apr 12 16:00:19.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:19.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:19.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:19.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:19.155: CEF-IDB: process queued interface events
*Apr 12 16:00:19.155: CEF-IDB: Virtual-Access2 coming up failed: interface not up
*Apr 12 16:00:19.155: CEF-IDB: restart queued interface events
*Apr 12 16:00:19.311: CEF: background resolution thread state:
*Apr 12 16:00:19.311: Thread fast_thread: Empty
*Apr 12 16:00:19.311: Thread todothread: Empty
*Apr 12 16:00:19.311: Thread slow_thread: Empty
*Apr 12 16:00:19.991: Vi2 LCP: TIMEout: State REQsent
*Apr 12 16:00:19.991: Vi2 LCP: O CONFREQ [REQsent] id 52 len 10
*Apr 12 16:00:19.991: Vi2 LCP: MagicNumber 0x164E89B9 (0x0506164E89B9)
*Apr 12 16:00:19.991:
*Apr 12 16:00:19.991: c820_vc_tx_start: idb = 0x82034CBC, cos_queue = 0x827C2DC8
*Apr 12 16:00:19.991: c820_aal_send: pak = 0x82345C50, vc = 1, q = 0
*Apr 12 16:00:19.995: pquicc_sar_safe_start: vc = 1
*Apr 12 16:00:20.311: CEF: background resolution thread state:
*Apr 12 16:00:20.311: Thread fast_thread: Empty
*Apr 12 16:00:20.311: Thread todothread: Empty
*Apr 12 16:00:20.311: Thread slow_thread: Empty
*Apr 12 16:00:21.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:21.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:21.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:21.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:21.311: CEF: background resolution thread state:
*Apr 12 16:00:21.311: Thread fast_thread: Empty
*Apr 12 16:00:21.311: Thread todothread: Empty
*Apr 12 16:00:21.311: Thread slow_thread: EmptyPQUICC_FEC: PHY 1C Read reg = 0val = BA00
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1B Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 1A Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
PQUICC_FEC: PHY 19 Read reg = 0 val = 800
*Apr 12 16:00:22.007: Vi2 LCP: TIMEout: State REQsent
*Apr 12 16:00:22.007: Vi2 LCP: O CONFREQ [REQsent] id 53 len 10
*Apr 12 16:00:22.no007: Vi2 LCP: MagicNumber 0x164E89B9 (0x0506164E89B9)
*Apr 12 16:00:22.007:
*Apr 12 16:00:22.007: c820_vc_tx_start: idb = 0x82034CBC, cos_queue = 0x827C2DC8
*Apr 12 16:00:22.007: c820_aal_send: pak = 0x82345C50, vc = 1, q = 0
*Apr 12 16:00:22.011: pquicc_sar_safe_start: vc = 1
*Apr 12 16:00:22.311: CEF: background resolution thread state:
*Apr 12 16:00:22.311: Thread fast_thread: Empty
*Apr 12 16:00:22.311: Thread todothread: Empty
*Apr 12 16:00:22.311: Thread slow_thread: Empty
*Apr 12 16:00: debug 23.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:23.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:23.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:23.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:23.311: CEF: background resolution thread state:
*Apr 12 16:00:23.311: Thread fast_thread: Empty
*Apr 12 16:00:23.311: Thread todothread: Empty
*Apr 12 16:00:23.311: Thread slow_thread: Empty
*Apr 12 16:00:24.023: Vi2 LCP: TIMEout: Statall port Statistics for unclassified packets is not turned on.
*Apr 12 16:00:24.023: Vi2 LCP: O CONFREQ [REQsent] id 54 len 10
*Apr 12 16:00:24.023: Vi2 LCP: MagicNumber 0x164E89B9 (0x0506164E89B9)
*Apr 12 16:00:24.023:
*Apr 12 16:00:24.023: c820_vc_tx_start: idb = 0x82034CBC, cos_queue = 0x827C2DC8
*Apr 12 16:00:24.023: c820_aal_send: pak = 0x82345C50, vc = 1, q = 0
*Apr 12 16:00:24.023: pquicc_sar_safe_start: vc = 1
*Apr 12 16:00:24.311: CEF: background resolution thread state:
*Apr 12 16:00:24.311: Thread fast_thread: Empty
*Apr 12 16:00:24.311: Thread todothread: Empty
*Apr 12 16:00:24.311: Thread slow_thread: Empty
*Apr 12 16:00:25.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:25.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:25.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:25.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:25.311: CEF: background resolution thread state:
*Apr 12 16:00:25.311: Thread fast_thread: Empty
*Apr 12 16:00:25.311: Thread todothread: Empty
*Apr 12 16:00:25.311: Thread slow_thread: Empty
*Apr 12 16:00:26.039: Vi2 LCP: TIMEout: State REQsent
*Apr 12 16:00:26.039: Vi2 LCP: O CONFREQ [REQsent] id 55 len 10
*Apr 12 16:00:26.039: Vi2 LCP: MagicNumber 0x164E89B9 (0x0506164E89B9)
*Apr 12 16:00:26.039:
*Apr 12 16:00:26.039: c820_vc_tx_start: idb = 0x82034CBC, cos_queue = 0x827C2DC8
*Apr 12 16:00:26.039: c820_aal_send: pak = 0x82345C50, vc = 1, q = 0
*Apr 12 16:00:26.039: pquicc_sar_safe_start: vc = 1
*Apr 12 16:00:26.311: CEF: background resolution thread state:
*Apr 12 16:00:26.311: Thread fast_thread: Empty
*Apr 12 16:00:26.311: Thread todothread: Empty
*Apr 12 16:00:26.311: Thread slow_thread: Empty
*Apr 12 16:00:27.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:27.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:27.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:27.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:27.311: CEF: background resolution thread state:
*Apr 12 16:00:27.311: Thread fast_thread: Empty
*Apr 12 16:00:27.311: Thread todothread: Empty
*Apr 12 16:00:27.311: Thread slow_thread: Empty
*Apr 12 16:00:28.055: Vi2 LCP: TIMEout: State REQsent
*Apr 12 16:00:28.055: Vi2 LCP: O CONFREQ [REQsent] id 56 len 10
*Apr 12 16:00:28.055: Vi2 LCP: MagicNumber 0x164E89B9 (0x0506164E89B9)
*Apr 12 16:00:28.055:
*Apr 12 16:00:28.055: c820_vc_tx_start: idb = 0x82034CBC, cos_queue = 0x827C2DC8
*Apr 12 16:00:28.055: c820_aal_send: pak = 0x82345C50, vc = 1, q = 0
*Apr 12 16:00:28.055: pquicc_sar_safe_start: vc = 1
*Apr 12 16:00:28.311: CEF: background resolution thread state:
*Apr 12 16:00:28.311: Thread fast_thread: Empty
*Apr 12 16:00:28.311: Thread todothread: Empty
*Apr 12 16:00:28.311: Thread slow_thread: Empty
*Apr 12 16:00:28.699: IP-Static: 0.0.0.0 0.0.0.0 Dialer0 Path = 1, route tableno change, recursive flag clear
*Apr 12 16:00:28.703: IP-ST: if_list try 2
*Apr 12 16:00:28.703: IP-ST: gw_list total 0, try 0, completed list TRUE
*Apr 12 16:00:28.703: IP-Static: all_list, time elapsed 4 ms
*Apr 12 16:00:28.719: RT: NET-RED 0.0.0.0/0
*Apr 12 16:00:28.723: CEF-Table(Default-table): Event up, default 0.0.0.0/0 (rdbs:1, flags:420025)
*Apr 12 16:00:28.723: CEF-IP: Prefix exists - no-op change
*Apr 12 16:00:29.147: ILMI(ATM0): Sending ilmiColdStart trap
*Apr 12 16:00:29.147: ILMI(ATM0): No ILMI VC found
*Apr 12 16:00:29.147: ILMI: Encapsulation error on o/g ILMI Pdu <ilmi_send_pkt>(ATM0)
*Apr 12 16:00:29.147: ILMI: Unable to Send Pdu out <ilmi_send_trap>
*Apr 12 16:00:29.311: CEF: background resolution thread state:
*Apr 12 16:00:29.311: Thread fast_thread: Empty
*Apr 12 16:00:29.311: Thread todothread: Empty
*Apr 12 16:00:29.311: Thread slow_thread: Empty
*Apr 12 16:00:29.431: corvil trace: "551108 cdkContext_TraceControl() self=0x822ec300, options=`none'"
CJ
Inviato: mer 20 set , 2006 11:25 am
da CJ
Still no luck with this line, Tiscali have run tests and say all is OK
Its an ADSL 2+ line (ITU G.992.5), however, the ATM interface detects ITU G.992.1 - is this not standard DSL? If so, does the 837 actually support ADSL2+, if not should I be looking at an 836?
sh dsl interface atm0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'GSPN'
Vendor Specific: 0x0000 0x0008
Vendor Country: 0x00 0xFF
Capacity Used: 80% 107%
Noise Margin: 16.0 dB 8.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 20.0 dB 8.5 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 1282 (2 spurious)
Activations: 1
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.220
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 8064 0 832 0
Reed-Solomon EC: 0 0 1 0
CRC Errors: 0 0 1 0
Header Errors: 0 0 0 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0
LOM Monitoring : Disabled
DMT Bits Per Bin
00: 0 0 0 0 0 0 0 7 8 9 A B C C C C
10: C C B B C B B B A A 9 9 9 9 0 0
20: 0 0 0 0 0 0 6 6 7 7 8 9 9 A A A
30: B B B B B B C C C C C C C C C C
40: 0 C C C C C C C C C D D D D D D
50: D D D D D D D D D 2 D D D D C D
60: D D D D D C C C C C C C C C C C
70: C C C C C C C B C B B B B B B B
80: B B B B B B B B B B B B B B B B
90: B B B B B B B B B B B B B B B B
A0: B B B B A A A A A A A A A A A A
B0: A A A A A A A A A A A A A A A A
C0: A A A A A A A A A A A 9 A 9 9 9
D0: 9 9 9 9 9 9 9 9 9 9 9 8 8 8 8 8
E0: 8 8 8 8 7 8 8 7 7 7 7 7 7 7 6 6
F0: 6 6 6 6 5 0 0 0 0 0 0 0 0 0 0 0
Training log buffer capability is not enabled yet.
Thanks Guys
CJ
Inviato: mer 20 set , 2006 1:42 pm
da MaiO
It's possible that you got (lucky you) a new ADSL (ADSL 2+). Unfortunatly 837 doesn't support the ADSL 2+. You need at least an 857 or 877 with latest IOS, or a modular router with HWIC-ADSL= (and not the old one WIC-ADSL=).
Bye
Inviato: lun 25 set , 2006 10:54 am
da CJ
MaiO ha scritto:It's possible that you got (lucky you) a new ADSL (ADSL 2+). Unfortunatly 837 doesn't support the ADSL 2+
On further investigation, it appears that the line is ADSL2 , not ADSL2+ - the 837 should work with this standard. I don't know if this helps but here are some more errors:
*Apr 22 19:12:23.998: IP: s=<eth0 IP> (local), d=<remote host IP> (Dialer0), le.n 100, encapsulation failed PQUICC_FEC: PHY 1C Read reg = 0 val = BA00
*Apr 22 19:12:59.618: CEF-IDB: Virtual-Access2 coming up failed: interface not up
CJ
Inviato: lun 25 set , 2006 11:19 am
da MaiO
Unfortunatly 837 doesn't support as ADSL2+ neither ADSL2.
Bye
Inviato: lun 25 set , 2006 3:40 pm
da CJ
MaiO ha scritto:Unfortunatly 837 doesn't support as ADSL2+ neither ADSL2.
Bye
Thanks MaiO, looks like I'll need to buy a 877
CJ
Inviato: mer 11 ott , 2006 10:02 am
da CJ
Good news => Cisco 877 installed - line detected
Bad news => line is flapping up and down every 5 minutes
*Mar 1 18:30:26.915: %LINK-3-UPDOWN: Interface Virtual Access2, changed state to down
*Mar 1 18:30:26.915: %DIALER-6-UNBIND: Interface Vi2 unbound from profile Di0
*Mar 1 18:30:27.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to down
*Mar 1 18:30:27.919: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 1 18:30:28.919: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down
*Mar 1 18:30:58.723: %LINK-3-UPDOWN: Interface ATM0, changed state to up
*Mar 1 18:30:59.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up
*Mar 1 18:31:03.407: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
*Mar 1 18:31:03.407: %DIALER-6-BIND: Interface Vi2 bound to profile Di0
*Mar 1 18:31:06.799: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to up
How do noise and attenuation levels look?
sh dsl int atm0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.5 (ADSL2+) Annex A
ITU STD NUM: 0x03 0x2
Chip Vendor ID: 'STMI' 'GSPN'
Chip Vendor Specific: 0x0000 0x000D
Chip Vendor Country: 0x0F 0xFF
Modem Vendor ID: 'CSCO' 'GSPN'
Modem Vendor Specific: 0x0000 0x0D00
Modem Vendor Country: 0xB5 0xFF
Serial Number Near: FCZ103920KH
Serial Number Far:
Modem Version Near: 12.4(4)T4
Modem Version Far:
Capacity Used: 67% 100%
Noise Margin: 16.5 dB 8.0 dB
Output Power: 20.5 dBm 12.5 dBm
Attenuation: 32.0 dB 9.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x92
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 8241 (0 spurious)
PHY Access Err: 0
Activations: 68
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
FW Version: 2.542
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 12285 0 1081
Cells: 0 296 0 344249
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 0 0
Header Errors: 0 0 0 0
Interleave Delay: 0 10 0 7
LOM Monitoring : Disabled
CJ
Inviato: mer 11 ott , 2006 10:27 am
da MaiO
Your version of IOS?
I heard that some older IOS's had many problems with line stability.
Try to update IOS. If this doesn't help you should call Tiscali to make a tests on the line.
Bye
Inviato: mer 11 ott , 2006 10:34 am
da CJ
MaiO ha scritto:Your version of IOS?
I heard that some older IOS's had many problems with line stability.
Try to update IOS. If this doesn't help you should call Tiscali to make a tests on the line.
Bye
IOS ver is quite recent - 12.4 specifically
c870-advsecurityk9-mz.124-4.T4
I will try and upgrade to see if solves the problem.
CJ
Inviato: mer 11 ott , 2006 11:23 am
da MaiO
It's quite old for an 877 (march 2006, one of the first IOS's for that router) (latest version is 12.4.9T1 - september 2006).
Bye
Inviato: mer 11 ott , 2006 11:32 am
da CJ
MaiO ha scritto:latest version is 12.4.9T1 - september 2006
Guess what, I've deleted the old image, loaded up 12.4.9T1 and rebooted - the router won't boot the imaage and I'm stuck with rommon mode
System Bootstrap, Version 12.3(8r)YI3, RELEASE SOFTWARE
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory
Booting flash:/c870-advipservicesk9-mz.124-9.T1.bin
ELF Loader: read error
Elf loader error
System Bootstrap, Version 12.3(8r)YI3, RELEASE SOFTWARE
Technical Support:
http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.
C870 series (Board ID: 1-148) platform with 131072 Kbytes of main memory
rommon 1 >
It doesn't get any better....
CJ
Inviato: mer 11 ott , 2006 1:10 pm
da CJ
Downloaded image again, would not load at all. Pulled doen previous revision (12.4.6) and router is back to normal
Thanks god for the tftpdnld command!
CJ
Inviato: mer 11 ott , 2006 3:12 pm
da MaiO
Test another version.
Bye