help su soho 77

Tutto ciò che ha a che fare con la configurazione di apparati Cisco (e non rientra nelle altre categorie)

Moderatore: Federico.Lagni

Rispondi
leiz83
Cisco fan
Messaggi: 30
Iscritto il: ven 26 ago , 2005 12:38 am
Località: Cesena

Non riesco a far navigare i pc dietro un soho 77.
Il router si collega, gli viene fornito un ip e riesce a pingare verso l'esterno.
Ma i computer non danno segno di navigare.
Allego conf e sh int:
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname cisco77
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$msde$6JkHPBy71V2NjvYcx0zwu0
!
clock timezone ROME 1
ip subnet-zero
ip name-server 212.216.112.112
ip dhcp excluded-address 10.198.30.1
!
ip dhcp pool DHCP
network 10.198.30.0 255.255.255.0
default-router 10.198.30.1
dns-server 212.216.112.112 212.216.172.62
!
!
!
!
interface Ethernet0
ip address 10.198.30.1 255.255.255.0
ip nat inside
hold-queue 100 out
!
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Dialer0
ip address negotiated
ip access-group 1 in
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication pap chap callin
ppp chap hostname *******
ppp chap password 0 *******
ppp pap sent-username ****** password 0 *******
!
ip nat inside source list 1 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
access-list 1 permit 10.198.30.0 0.0.0.255
dialer-list 1 protocol ip permit
!
line con 0
stopbits 1
line vty 0 4
password ********
login



sh int:
ATM0 is up, line protocol is up
Hardware is PQUICC_SAR (with Alcatel ADSL Module)
MTU 1500 bytes, sub MTU 1500, BW 320 Kbit, DLY 80 usec,
reliability 215/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 1024 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 1 packets/sec
213 packets input, 9715 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
300 packets output, 14013 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
Dialer0 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address is 151.51.228.1/32
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi2
Last input never, output never, output hang never
Last clearing of "show interface" counters 00:07:35
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
206 packets input, 9628 bytes
293 packets output, 13913 bytes
Bound to:
Virtual-Access2 is up, line protocol is up
Hardware is Virtual Access interface
MTU 1500 bytes, BW 0 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Open
Listen: CDPCP
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 10Mb/s
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
--More--
*Mar 1 00:14:31.051: %SYS-5-CONFIG_I: Configured from console by vty0 (10 Input queue: 2/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/100 (size/max)
5 minute input rate 2000 bits/sec, 2 packets/sec
5 minute output rate 2000 bits/sec, 2 packets/sec
1373 packets input, 89335 bytes, 0 no buffer
Received 10 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
1078 packets output, 152921 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Virtual-Access1 is up, line protocol is up
Hardware is Virtual Access interface
MTU 1500 bytes, BW 100000 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed
Base PPPoATM vaccess
Vaccess status 0x40, loopback not set
DTR is pulsed for 5 seconds on reset
Last input never, output never, output hang never
Last clearing of "show interface" counters 00:14:24
Input queue: 0/4096/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Virtual-Access2 is down, line protocol is down
Hardware is Virtual Access interface
MTU 1500 bytes, BW 0 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Closed
PPPoATM vaccess, cloned from Dialer0
Vaccess status 0x4
Bound to ATM0 VCD: 1, VPI: 8, VCI: 35, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Last input 00:02:05, output never, output hang never
Last clearing of "show interface" counters 00:13:52
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
356 packets input, 20940 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
515 packets output, 24867 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Avatar utente
andrewp
Messianic Network master
Messaggi: 2199
Iscritto il: lun 13 giu , 2005 7:32 pm
Località: Roma

I pc hanno dns?L'interfaccia eth è in no shut?
Manipolatore di bit.
leiz83
Cisco fan
Messaggi: 30
Iscritto il: ven 26 ago , 2005 12:38 am
Località: Cesena

l'eth0 è up (vedi conf e cmq ci sto lavorando in telnet)
il dns c'è e cmq per ora sto provando solo dei ping -t
devo fornirti altro?
leiz83
Cisco fan
Messaggi: 30
Iscritto il: ven 26 ago , 2005 12:38 am
Località: Cesena

risolto aggiungendo:
access-list 1 permit any
qualcuno mi riesce a spiegare perchè non bastava :
access-list 1 permit 10.198.30.0 0.0.0.255
?
la rete interna è 10.198.30.0/24...
ho bisogno di capire
Rispondi