Aiuto soho77

[psicoticos]

Ciao a tutti sono nuovo.

Ho un problema stavo provando a recuperare la passw del mio soho 77 che mi hanno dato ma devo avere sbagliato qualche cosa ed ora non parte pià come era prima cioè in parole povere mi esce così nella consolle

ROUTER>

Non so più come fare
Chi mi darebbe una mano?

wuesta è l'ultima cosa che ho fatto


--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: y

At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.

Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system

Would you like to enter basic management setup? [yes/no]: n

First, would you like to see the current interface summary? [yes]: n

Configuring global parameters:

Enter host name [Router]:

The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: 03041317

The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: 03041317
% Please choose a password that is different from the enable secret
Enter enable password: 03041317

The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: 5 $1$MIxK$pFq66fOgVWlXo1Z5vCIPM
Configure SNMP Network Management? [yes]:
Community string [public]:
Configure IP? [yes]:
Configure IGRP routing? [yes]: n
Configure RIP routing? [no]: n
Configure bridging? [no]: n

Configuring interface parameters:

Do you want to configure ATM0 interface? [yes]: n

Do you want to configure Ethernet0 interface? [yes]: s
% Please answer 'yes' or 'no'.

Do you want to configure Ethernet0 interface? [yes]:
Configure IP on this interface? [yes]:
IP address for this interface: 192.168.0.1
Subnet mask for this interface [255.255.255.0] :
Class C network is 192.168.0.0, 24 subnet bits; mask is /24

The following configuration command script was created:

hostname Router
enable secret 5 $1$2BmC$3muKtHoxQqPGA.lj8rFyi.
enable password 03041317
line vty 0 4
password 5 $1$MIxK$pFq66fOgVWlXo1Z5vCIPM
snmp-server community public
!
ip routing
no bridge 1
!
interface ATM0
shutdown
no ip address
!
interface Ethernet0
ip address 192.168.0.1 255.255.255.0
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
end


[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.

Enter your selection [2]:
The enable password you have chosen is the same as your enable secret.
This is not recommended. Re-enter the enable password.
Invalid encryption type: 5

Building configuration...
Use the enabled mode 'configure' command to modify this configuration.


Press RETURN to get started!


00:00:14: %LINK-3-UPDOWN: Interface Ethernet0, changed state to up
00:00:17: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed sta
te to up
00:00:19: %LINK-3-UPDOWN: Interface ATM0, changed state to down
00:00:20: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to
down
00:03:17: %LINK-5-CHANGED: Interface ATM0, changed state to administratively dow
n
00:03:20: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) SOHO70 Software (SOHO70-Y1-M), Version 12.1(5)YB5, EARLY DEPLOYMENT REL
EASE SOFTWARE (fc2)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Fri 15-Feb-02 21:41 by yiyan
Router>exit

[wiwan]

Il processo di password recovery è sostanzialmente il seguente:

FASE 1: Settare il router (tramite il configuration register) in modo da non utilizzare la configurazione presente nella NVRAM;
FASE 2: Riavviare il router;
FASE 3: Entrare in modalità Privileged EXEC mode (che a questo punto sarà priva di password di accesso);
FASE 4: In caso di password non crittografate sarà possibile visualizzare dal file di configurazione nella NVRAM, altrimenti sarà necessario settare una nuova password, nel caso peggiore bisognera caricare una nuova configurazione;
FASE 5: Settare nuovamente il router per leggere il file di configurazione nella NVRAM;
FASE 6: Riavviare il router

Per maggiori info:
http://www.cisco.com/warp/public/474/ps ... ho77.shtml

[psicoticos]

Grazie

Adesso mi da questo errore quando faccio ctrl/pausa
perchè?


*** Machine Check Exception ***
PC = 0x80008284, Vector = 0x200, SP = 0x800049f4

monitor: command "" aborted due to exception

*** Machine Check Exception ***
PC = 0x80008284, Vector = 0x200, SP = 0x800049f4