router c1751v

Tutto ciò che ha a che fare con la configurazione di apparati Cisco (e non rientra nelle altre categorie)

Moderatore: Federico.Lagni

Rispondi
hyde.78
n00b
Messaggi: 9
Iscritto il: mer 08 giu , 2005 6:14 pm

ciao ragazzi,
io possiedo un c1751v ma credo di avere un problema:
quando inserisco le tre schede (ad esempio wic 1t slot 0-wic 1 BS/T slot 1 e wic 1 ADSL slot 2),la scheda che inserisco nello slot 2 (in questo caso la wic 1 ADSL) non me la legge quando faccio uno show ver.
E' UN PROLìBLEMA DI VERSIONE SECONDO VOI?
O UN PROBLEMA FISICO DEL ROUTER?
SOTTO RIPORTO LO SHOW VER:


Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-SV3Y-M), Version 12.2(8)T10, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 30-May-03 07:07 by kellythw
Image text-base: 0x80008108, data-base: 0x80CD6A50

ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)

Router uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:175cvp122.8T10"

cisco 1751 (MPC860P) processor (revision 0x300) with 52429K/13107K bytes of memory.
Processor board ID FOC07260NTN (2650633480), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial(sync/async) network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102


GRAZIE DELL'ATTENZIONE!!!!!!!!!!
Avatar utente
TheIrish
Site Admin
Messaggi: 1840
Iscritto il: dom 14 mar , 2004 11:26 pm
Località: Udine
Contatta:

Forse dico una pippata (non ho presente il router), ma non è che inserisci una WIC in uno slot VIC?
Avatar utente
TheIrish
Site Admin
Messaggi: 1840
Iscritto il: dom 14 mar , 2004 11:26 pm
Località: Udine
Contatta:

ehm....è una pippata......li slot dei 1751-V si autoadattano....magari averne uno!
eh, buono a sapersi ;)
hyde.78
n00b
Messaggi: 9
Iscritto il: mer 08 giu , 2005 6:14 pm

mi hanno detto che in quello slot ci si possono mettere solo vic fxs per la voce. puo' essere giusto?
Renato.Efrati
Holy network Shaman
Messaggi: 637
Iscritto il: gio 07 apr , 2005 9:30 pm
Località: Cisco Systems Inc. West Tasman Drive 170, San Jose CA
Contatta:

netkiller ha scritto:
TheIrish ha scritto:Forse dico una pippata (non ho presente il router), ma non è che inserisci una WIC in uno slot VIC?
ehm....è una pippata......li slot dei 1751-V si autoadattano....magari averne uno!

Per hyde.78:
Il problema è che hai bisogno di un IOS con feature IP PLUS o ADSL altrimenti il router non la riconosce.

MAtteo

eh no ti sbagli caro il problema e' ke nello slot 2 , SE LEGGI c'e' anche scritto, si possono mettere solo schede voice

CCIE Routing & Switching # 20567
CCNP R&S - CCNP Sec - CCNP Collaboration - CCNP Datacenter - CCDP - VCP6-DCV

Avatar utente
TheIrish
Site Admin
Messaggi: 1840
Iscritto il: dom 14 mar , 2004 11:26 pm
Località: Udine
Contatta:

ah, allora non era una pippata ;)
Renato.Efrati
Holy network Shaman
Messaggi: 637
Iscritto il: gio 07 apr , 2005 9:30 pm
Località: Cisco Systems Inc. West Tasman Drive 170, San Jose CA
Contatta:

TheIrish ha scritto:ah, allora non era una pippata ;)
gia' lol hai quasi sempre ragione :P

CCIE Routing & Switching # 20567
CCNP R&S - CCNP Sec - CCNP Collaboration - CCNP Datacenter - CCDP - VCP6-DCV

hyde.78
n00b
Messaggi: 9
Iscritto il: mer 08 giu , 2005 6:14 pm

grazie ragazzi!!!
Rispondi