CiscoForums.it

Salve ho problemi nella configurazione d un 1751 sul quale sono installate una seriale ed una wic adsl.
L'ho acquistato x fare esperienza come studente CCNA.
Qualcuno sarebbe gentile da inviarmi un config per farlo funzionare con una 7 mega tiscali?
Ho provato varie config trovate in rete ma nessuna va.Non trovo nessuno che sappia come far lavorare la wic adsl che ho comprato in seguito.
Grazie Paolo

Controlla che la IOS installata supporti la WIC-1ADSL che hai comprato in seguito… potresti aver bisogno di aggiornarla.

Ciao!

Ciao grazie per la risposta.se vuoi ti posto la configurazione.l'IOS l'ho rimediato.ti faccio avere il tutto pero se puoi mi posti un config generico per lavorare in adsl?
ciao

Le configurazioni generiche sono in questa sezione del forum, marcate come "importanti"! Al massimo cambiano i nomi delle interfacce (ad es. ATM0/0 anziché ATM0).

Se vuoi essere sicuro che la WIC sia riconosciuta, controlla l'output del comando "show diag" (e in caso posta anche "show hardware" e "show version"…)

Ciao!

ciao ho appena preso tutto quello che seve.Ho fatto anche una espansione ram che non riuscivo a caricare cert IOS.
Fammi sapere
Cisco IOS Software, C1700 Software (C1700-SY7-M), Version 12.4(10), RELEASE SOFT
WARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 15-Aug-06 23:54 by prod_rel_team

ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)

Router uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:c1700-sy7-mz.124-10.bin"

Cisco 1751 (MPC860P) processor (revision 0x700) with 81920K/16384K bytes of memo
ry.
Processor board ID FOC07210FTF (3886772592), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 FastEthernet interface
1 Serial(sync/async) interface
1 ATM interface
32K bytes of NVRAM.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x3922

-----------------------------------------------------------------------------------------

Current configuration : 1387 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
memory-size iomem 25
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
!
!
!
!
!
!
!
ip cef
no ip domain lookup
ip name-server 213.205.32.70
ip name-server 213.205.36.70
ip name-server 151.99.125.3
ip name-server 212.216.112.222
!
!
!
!
interface FastEthernet0/0
no ip address
shutdown
speed auto
!
interface Serial0/0
no ip address
shutdown
!
interface ATM1/0
no ip address
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
!
interface Dialer0
description Interfaccia Dialer1 - Connessione TISCALI ADSL 7Mbit/s
bandwidth 2464
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp pap sent-username xxxxxxxxxxx password xxxxxxxxx
!
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
ip nat translation timeout 420
ip nat translation tcp-timeout 120
ip nat translation pptp-timeout 420
ip nat translation icmp-timeout 1
ip nat translation max-entries 1000
ip nat inside source list nat interface Dialer0 overload
!
!
!
permit ip 192.168.0.0 0.0.0.255 any
permit icmp 192.168.0.0 0.0.0.255 any
!
!
control-plane
!
!
line con 0
speed 115200
line aux 0
line vty 0 4
!
end
--------------------------------------------------------------------------------

Questo è lo show hardware


Cisco IOS Software, C1700 Software (C1700-SY7-M), Version 12.4(10), RELEASE SOFT
WARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Tue 15-Aug-06 23:54 by prod_rel_team

ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)

Router uptime is 6 minutes
System returned to ROM by power-on
System image file is "flash:c1700-sy7-mz.124-10.bin"

Cisco 1751 (MPC860P) processor (revision 0x700) with 81920K/16384K bytes of memo
ry.
Processor board ID FOC07210FTF (3886772592), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 FastEthernet interface
1 Serial(sync/async) interface
1 ATM interface
32K bytes of NVRAM.
16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x3922

Dimenticavo questo è lo show diag:

Router#show diag
Slot 0:
C1751 1FE VE DV Mainboard Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 7.0
PCB Serial Number : FOC07210FTF
Part Number : 73-5128-07
Board Revision : A0
Fab Version : 04
Product (FRU) Number : CISCO1751
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 02 4D 41 07 00 C1 8B 46 4F 43 30 37 32
0x10: 31 30 46 54 46 82 49 14 08 07 42 41 30 02 04 FF
0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC/VIC Slot 0:
Serial 1T
Hardware revision 1.0 Board revision M0
Serial number 0030371676 Part number 800-01514-01
FRU Part Number WIC-1T=

Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 02 01 00 01 CF 6F 5C 50 05 EA 01 00 00 00 00
0x30: B0 00 00 00 03 05 10 01 FF FF FF FF FF FF FF FF

WIC/VIC Slot 1:
Alcatel 20150 ADSL WIC
Daughter card-Version 4 TLV Cookie Format
Hardware Revision : 2.3
Part Number : 73-4771-08
Board Revision : B0
Deviation Number : 1-200
Fab Version : 05
PCB Serial Number : FOC07080Q1J
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : WIC-1ADSL=

Se guardi bene le config base di esempio (come questa), sotto l'interfaccia ATM, trovi la parte "pvc" che nella tua configurazione manca.

Per la versione non dovresti avere problemi perché vedo che la WIC-1ADSL con relativa interfaccia ATM viene riconosciuta benissimo.

Ciao!

Ciao ho gia provato la configurazione base anche se con piccole modifiche ma non va lo stesso.
potresi postarmela tu? adattata x tiscali cosi cerco di capire qual'è il mio errore.
Spero tu possa aiutarmi...
Grazie Paolo

Ciao ho appena rifatto la conf a mano seguendo una procedura passo passo commentata di tiscali per l'827 ma che ho aggiustato per il 1751 (tipo ethenet a 100 invece che 10).
Mi sembra quasi uguale a quella di base del sito.
Fammi sapere che ne pensi.Non riesco solo ad attivare il dhcp e deve dare ip fisso al mio portatile.
Aspetto tue notizie.
Se potessi farmi avere un numero in privato posso farti uno squillo,magari a voce è meglio.Grazie per il momento.

Dimenticavo la config....

Current configuration : 1353 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
enable secret 5 xxxxxxx
enable password xxxxxxx
!
no aaa new-model
memory-size iomem 25
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
no ip routing
!
!
!
!
no ip cef
ip name-server 213.205.32.70
ip name-server 213.205.36.70
!
!
!
!
interface FastEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip route-cache
speed auto
full-duplex
!
interface Serial0/0
no ip address
no ip route-cache
shutdown
!
interface ATM1/0
no ip address
no ip route-cache
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname xxxxxxxx
ppp chap password 0 xxxxxxx
ppp pap sent-username xxxxxxx password 0 xxxxxxx
!
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
ip nat inside source list 1 interface Dialer0 overload
!
!
access-list 1 permit 192.168.1.0 0.0.0.255
snmp-server community public RO
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
password xxxxxxx
login
!
end

hai ip routing ed ip cef disabilitati; attivali perche' sono fondamentali, a prescindere dall'adsl.

posta anche un debug del PPP


ciao

Ciao se ho fatto bene questo dovrebbe essere il debug:

Router>
*Mar 1 12:57:00.775: %LINK-3-UPDOWN: Interface ATM1/0, changed state to up
*Mar 1 12:57:01.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM1/0, ch
anged state to up
*Mar 1 12:57:08.623: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state t
o up
*Mar 1 12:57:08.623: %DIALER-6-BIND: Interface Vi2 bound to profile Di0
*Mar 1 12:57:08.623: Vi2 PPP: Using dialer call direction
*Mar 1 12:57:08.623: Vi2 PPP: Treating connection as a callout
*Mar 1 12:57:08.627: Vi2 PPP: Session handle[DE000004] Session id[2]
*Mar 1 12:57:08.627: Vi2 PPP: Authorization required
*Mar 1 12:57:08.627: Vi2 PPP: No remote authentication for call-out
*Mar 1 12:57:12.683: Vi2 PPP: No authorization without authentication
*Mar 1 12:57:12.731: Vi2 CHAP: I CHALLENGE id 1 len 36 from "c10008.rms-atm1"
*Mar 1 12:57:12.735: Vi2 CHAP: Using hostname from interface CHAP
*Mar 1 12:57:12.735: Vi2 CHAP: Using password from interface CHAP
*Mar 1 12:57:12.735: Vi2 CHAP: O RESPONSE id 1 len 30 from "mirrorweb"
*Mar 1 12:57:12.879: Vi2 CHAP: I SUCCESS id 1 len 4
*Mar 1 12:57:13.879: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Ac
cess2, changed state to up
*Mar 1 12:58:25.635: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern
et0/0, changed state to up
Router>

Scusa ma sono uno studente in apprendimento.
Fammi sapere....
Grazie

Il PPP e' salito... hai impostato correttamente i DNS? dovresti navigare...
figo... Cisco 10000 da parte di tiscali