Configurazione 877 per alice 20 Mega

[Wizard]

Ci fai vedere un bel "sh run" del router con la conf aggiornata?!
La loopback no, non ti serve.

[fabioV]

Ci fai vedere un bel "sh run" del router con la conf aggiornata?!
La loopback no, non ti serve.

eccola, la allego. grazie di tutto.

[Wizard]

interface Vlan1
description Virtual Web interface
ip address xxx.xxx.xxx.xxx 255.255.255.240

Sicuro...? quella subnet indica 14 host utilizzabili...mi sa che la tua ne abbia solo 6 e quindi è 255.255.255.248

Fai la modifica poi dai router fai:

ping 151.1.1.1 source vlan 1

[fabioV]

interface Vlan1
description Virtual Web interface
ip address xxx.xxx.xxx.xxx 255.255.255.240

Sicuro...? quella subnet indica 14 host utilizzabili...mi sa che la tua ne abbia solo 6 e quindi è 255.255.255.248

Fai la modifica poi dai router fai:

ping 151.1.1.1 source vlan 1

si sicuro, il range di ip è di 16, quindi 14 utilizzabili
..ma infatti con un linksys che supporta adsl2+ non ho alcun problema, la linea raggiunge picchi di 18 mb..
con l'877 non raggiunge nemmeno i 2 mb dell'adsl 1..

[Wizard]

Quindi ora va ma va lento?
Se è così:

1) Aggiorna la ios
2) Aggiorna il firmware del modulo adsl
3) Cambia il parametro "dsl operating mode" in auto

[fabioV]

Quindi ora va ma va lento?
Se è così:

1) Aggiorna la ios
2) Aggiorna il firmware del modulo adsl
3) Cambia il parametro "dsl operating mode" in auto

ciao , il problema l'ho risolto con l'altro router e uno me l'hanno sostituito .
Il problema è che non so come aggiornare i lfirmware del modulo ADSL ... qualcuno sa aiutarmi? nell'altro router lo aveva fatto un mio collega..

[Wizard]

E' una stupidata ma devi avere il firmware nuovo e se non hai un account CCO mi sa che fai fatica a scaricarlo...

[fabioV]

E' una stupidata ma devi avere il firmware nuovo e se non hai un account CCO mi sa che fai fatica a scaricarlo...

il firmwarece l'ho già non so come caricarlo.. penso sia un oerazione tipo TFTP ma non l'ho mai eseguita, sai consigliarmi?

[Wizard]

La avevo già postata cmq...:

Cisco Systems, Inc.
Firmware File Version 3.0.10
September 2006

Copyright (C) 1999-2006 Cisco Systems, Inc. All rights reserved. Printed in the
USA. Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks
of Cisco Systems, Inc. in the U.S. and certain other countries. All other
trademarks mentioned in this document are the property of their registered
Owners .


=========================================================================
Table of Contents
=========================================================================

1. Firmware file details and purpose

2. Target Platforms

3. Instructions for upgrading the firmware file

4. Caveats

=========================================================================


1. Firmware file details and purpose

The Firmware file version (3.0.10) resolves some of the specific ADSL interoperability issues (Refer to Caveats). IOS release 12.4(6)T is recommended with this firmware version.

Refer individual platform data sheets for complete DSLAM interoperability details

2. Target Platforms

Loading of the firmware file from flash separate from IOS is supported on all the Fixed ADSL Integrated Services Routers. Following is the list of platforms supported:

1 .Cisco 857
2. Cisco 876, Cisco 877
3. Cisco 1801, Cisco 1802
4. HWIC-1ADSL1, HWIC-1ADSLI, HWIC-ADSL-B/ST, HWIC-ADSLI-B/ST




3. Instructions for upgrading the firmware file

1. Download the file and rename the file "adsl_alc_20190.bin".
2. Copy the firmware file to the flash:
3. For the new firmware to take effect, reboot the device.
4. The “show dsl interface atm 0” output gives the details of the firmware file in use



Snapshot example taken from the output of “Show dsl interface atm 0” command

Firmware file in flash is used
Firmware file embedded in IOS is used
Init FW: init_AMR-3.0.010.bin
Operation FW: AMR-3.0.010.bin
FW Version: 3.0.10
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42


Note:

 The firmware file should not be renamed when being copied to the flash , Since the router looks for the presence of file named "adsl_alc_20190.bin" to initiate the flash upgrade process
 If IOS is now able to find a valid firmware in the flash then it would always use that rather than the firmware embedded in IOS .If users want to use the embedded firmware, they have to ensure that there is no valid firmware file in flash.


4. Caveats

The following issues are fixed in the latest firmware 3.0.10

1) CSCse51699 : 1801 can not train to HiFOCUS 4 in operating mode auto.

[fabioV]

La avevo già postata cmq...:

Cisco Systems, Inc.
Firmware File Version 3.0.10
September 2006

Copyright (C) 1999-2006 Cisco Systems, Inc. All rights reserved. Printed in the
USA. Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks
of Cisco Systems, Inc. in the U.S. and certain other countries. All other
trademarks mentioned in this document are the property of their registered
Owners .
il fatto è che non ricordavo se andava inserita nella flash, inoltre il comando che mi hai mandato lo cercavo da 2 giorni -.- me ne ricordavo solo una parte.. provo subito e ti faccio sapere , grazie infinite!
(ma che lavoro fai?)

=========================================================================
Table of Contents
=========================================================================

1. Firmware file details and purpose

2. Target Platforms

3. Instructions for upgrading the firmware file

4. Caveats

=========================================================================


1. Firmware file details and purpose

The Firmware file version (3.0.10) resolves some of the specific ADSL interoperability issues (Refer to Caveats). IOS release 12.4(6)T is recommended with this firmware version.

Refer individual platform data sheets for complete DSLAM interoperability details

2. Target Platforms

Loading of the firmware file from flash separate from IOS is supported on all the Fixed ADSL Integrated Services Routers. Following is the list of platforms supported:

1 .Cisco 857
2. Cisco 876, Cisco 877
3. Cisco 1801, Cisco 1802
4. HWIC-1ADSL1, HWIC-1ADSLI, HWIC-ADSL-B/ST, HWIC-ADSLI-B/ST




3. Instructions for upgrading the firmware file

1. Download the file and rename the file "adsl_alc_20190.bin".
2. Copy the firmware file to the flash:
3. For the new firmware to take effect, reboot the device.
4. The “show dsl interface atm 0” output gives the details of the firmware file in use



Snapshot example taken from the output of “Show dsl interface atm 0” command

Firmware file in flash is used
Firmware file embedded in IOS is used
Init FW: init_AMR-3.0.010.bin
Operation FW: AMR-3.0.010.bin
FW Version: 3.0.10
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42


Note:

 The firmware file should not be renamed when being copied to the flash , Since the router looks for the presence of file named "adsl_alc_20190.bin" to initiate the flash upgrade process
 If IOS is now able to find a valid firmware in the flash then it would always use that rather than the firmware embedded in IOS .If users want to use the embedded firmware, they have to ensure that there is no valid firmware file in flash.


4. Caveats

The following issues are fixed in the latest firmware 3.0.10

1) CSCse51699 : 1801 can not train to HiFOCUS 4 in operating mode auto.

[fabioV]

La avevo già postata cmq...:

Cisco Systems, Inc.
Firmware File Version 3.0.10
September 2006

Copyright (C) 1999-2006 Cisco Systems, Inc. All rights reserved. Printed in the
USA. Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks
of Cisco Systems, Inc. in the U.S. and certain other countries. All other
trademarks mentioned in this document are the property of their registered
Owners .
il fatto è che non ricordavo se andava inserita nella flash, inoltre il comando che mi hai mandato lo cercavo da 2 giorni -.- me ne ricordavo solo una parte.. provo subito e ti faccio sapere , grazie infinite!
(ma che lavoro fai?)

=========================================================================
Table of Contents
=========================================================================

1. Firmware file details and purpose

2. Target Platforms

3. Instructions for upgrading the firmware file

4. Caveats

=========================================================================


1. Firmware file details and purpose

The Firmware file version (3.0.10) resolves some of the specific ADSL interoperability issues (Refer to Caveats). IOS release 12.4(6)T is recommended with this firmware version.

Refer individual platform data sheets for complete DSLAM interoperability details

2. Target Platforms

Loading of the firmware file from flash separate from IOS is supported on all the Fixed ADSL Integrated Services Routers. Following is the list of platforms supported:

1 .Cisco 857
2. Cisco 876, Cisco 877
3. Cisco 1801, Cisco 1802
4. HWIC-1ADSL1, HWIC-1ADSLI, HWIC-ADSL-B/ST, HWIC-ADSLI-B/ST




3. Instructions for upgrading the firmware file

1. Download the file and rename the file "adsl_alc_20190.bin".
2. Copy the firmware file to the flash:
3. For the new firmware to take effect, reboot the device.
4. The “show dsl interface atm 0” output gives the details of the firmware file in use



Snapshot example taken from the output of “Show dsl interface atm 0” command

Firmware file in flash is used
Firmware file embedded in IOS is used
Init FW: init_AMR-3.0.010.bin
Operation FW: AMR-3.0.010.bin
FW Version: 3.0.10
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42


Note:

 The firmware file should not be renamed when being copied to the flash , Since the router looks for the presence of file named "adsl_alc_20190.bin" to initiate the flash upgrade process
 If IOS is now able to find a valid firmware in the flash then it would always use that rather than the firmware embedded in IOS .If users want to use the embedded firmware, they have to ensure that there is no valid firmware file in flash.


4. Caveats

The following issues are fixed in the latest firmware 3.0.10

1) CSCse51699 : 1801 can not train to HiFOCUS 4 in operating mode auto.

il responso al comando (a router non in rete ma solo via terminal):
ATM0
Alcatel 20190 chipset information

Line has not yet been activated.

Modem Status: Down (DMTDSL_DO_OPEN)
DSL Mode: Unknown
Interrupts: 12372 (0 spurious)
PHY Access Err: 0
Activations: 0
LED Status: OFF
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-3.0.014_no_bist.bin
Operation FW: AMR-3.0.014.bin
FW Source: embedded
eppure avevo caricato in tftp questo file:
adsl_alc_20190_3.0.10.bin
facendo /copy tftp flash/
ho sbagliato qualcosa mi sa..

[fabioV]

La avevo già postata cmq...:

Cisco Systems, Inc.
Firmware File Version 3.0.10
September 2006

Copyright (C) 1999-2006 Cisco Systems, Inc. All rights reserved. Printed in the
USA. Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks
of Cisco Systems, Inc. in the U.S. and certain other countries. All other
trademarks mentioned in this document are the property of their registered
Owners .
il fatto è che non ricordavo se andava inserita nella flash, inoltre il comando che mi hai mandato lo cercavo da 2 giorni -.- me ne ricordavo solo una parte.. provo subito e ti faccio sapere , grazie infinite!
(ma che lavoro fai?)

=========================================================================
Table of Contents
=========================================================================

1. Firmware file details and purpose

2. Target Platforms

3. Instructions for upgrading the firmware file

4. Caveats

=========================================================================


1. Firmware file details and purpose

The Firmware file version (3.0.10) resolves some of the specific ADSL interoperability issues (Refer to Caveats). IOS release 12.4(6)T is recommended with this firmware version.

Refer individual platform data sheets for complete DSLAM interoperability details

2. Target Platforms

Loading of the firmware file from flash separate from IOS is supported on all the Fixed ADSL Integrated Services Routers. Following is the list of platforms supported:

1 .Cisco 857
2. Cisco 876, Cisco 877
3. Cisco 1801, Cisco 1802
4. HWIC-1ADSL1, HWIC-1ADSLI, HWIC-ADSL-B/ST, HWIC-ADSLI-B/ST




3. Instructions for upgrading the firmware file

1. Download the file and rename the file "adsl_alc_20190.bin".
2. Copy the firmware file to the flash:
3. For the new firmware to take effect, reboot the device.
4. The “show dsl interface atm 0” output gives the details of the firmware file in use



Snapshot example taken from the output of “Show dsl interface atm 0” command

Firmware file in flash is used
Firmware file embedded in IOS is used
Init FW: init_AMR-3.0.010.bin
Operation FW: AMR-3.0.010.bin
FW Version: 3.0.10
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42


Note:

 The firmware file should not be renamed when being copied to the flash , Since the router looks for the presence of file named "adsl_alc_20190.bin" to initiate the flash upgrade process
 If IOS is now able to find a valid firmware in the flash then it would always use that rather than the firmware embedded in IOS .If users want to use the embedded firmware, they have to ensure that there is no valid firmware file in flash.


4. Caveats

The following issues are fixed in the latest firmware 3.0.10

1) CSCse51699 : 1801 can not train to HiFOCUS 4 in operating mode auto.

allora, nella flash mi vede il file, menre se eseguo il comando mi visualizza il firmware AMR-3.0.014.bin
come faccio?.. io ho fatto copy tftp flash e me l'ha copiato, ma è coem se mi vedesse l'altro integrato con l'IOS..
se potete aiutarmi..ancora una volta.. :

[fabioV]

La avevo già postata cmq...:

Cisco Systems, Inc.
Firmware File Version 3.0.10
September 2006

Copyright (C) 1999-2006 Cisco Systems, Inc. All rights reserved. Printed in the
USA. Cisco, Cisco Systems, and the Cisco Systems logo are registered trademarks
of Cisco Systems, Inc. in the U.S. and certain other countries. All other
trademarks mentioned in this document are the property of their registered
Owners .
il fatto è che non ricordavo se andava inserita nella flash, inoltre il comando che mi hai mandato lo cercavo da 2 giorni -.- me ne ricordavo solo una parte.. provo subito e ti faccio sapere , grazie infinite!
(ma che lavoro fai?)

=========================================================================
Table of Contents
=========================================================================

1. Firmware file details and purpose

2. Target Platforms

3. Instructions for upgrading the firmware file

4. Caveats

=========================================================================


1. Firmware file details and purpose

The Firmware file version (3.0.10) resolves some of the specific ADSL interoperability issues (Refer to Caveats). IOS release 12.4(6)T is recommended with this firmware version.

Refer individual platform data sheets for complete DSLAM interoperability details

2. Target Platforms

Loading of the firmware file from flash separate from IOS is supported on all the Fixed ADSL Integrated Services Routers. Following is the list of platforms supported:

1 .Cisco 857
2. Cisco 876, Cisco 877
3. Cisco 1801, Cisco 1802
4. HWIC-1ADSL1, HWIC-1ADSLI, HWIC-ADSL-B/ST, HWIC-ADSLI-B/ST




3. Instructions for upgrading the firmware file

1. Download the file and rename the file "adsl_alc_20190.bin".
2. Copy the firmware file to the flash:
3. For the new firmware to take effect, reboot the device.
4. The “show dsl interface atm 0” output gives the details of the firmware file in use



Snapshot example taken from the output of “Show dsl interface atm 0” command

Firmware file in flash is used
Firmware file embedded in IOS is used
Init FW: init_AMR-3.0.010.bin
Operation FW: AMR-3.0.010.bin
FW Version: 3.0.10
Init FW: embedded
Operation FW: embedded
FW Version: 2.5.42


Note:

 The firmware file should not be renamed when being copied to the flash , Since the router looks for the presence of file named "adsl_alc_20190.bin" to initiate the flash upgrade process
 If IOS is now able to find a valid firmware in the flash then it would always use that rather than the firmware embedded in IOS .If users want to use the embedded firmware, they have to ensure that there is no valid firmware file in flash.


4. Caveats

The following issues are fixed in the latest firmware 3.0.10

1) CSCse51699 : 1801 can not train to HiFOCUS 4 in operating mode auto.

allora, nella flash mi vede il file, menre se eseguo il comando mi visualizza il firmware AMR-3.0.014.bin
come faccio?.. io ho fatto copy tftp flash e me l'ha copiato, ma è coem se mi vedesse l'altro integrato con l'IOS..
se potete aiutarmi..ancora una volta.. :

[Wizard]

Rename the file "adsl_alc_20190.bin".

[fabioV]

Rename the file "adsl_alc_20190.bin".

lo farei ma nelal flash c'è solo il file dell IOS e il firmware corretto! per questo sono un pò basito -.-