Configurazione VWIC2-2MFT-t1/E1

[cluchetti]

Ciao a tutti,

Sul cisco 2851 ho una VWIC2-2MFT-t1/E1 che cerco di configurare
Appena do il comando: “card type e1 0 0”

Mi rimane l’interfaccia in down

Router#sh controller E1
E1 0/0/0 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20060707, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (662 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 662 Unavail Secs
Total Data (last 2 15 minute intervals):
2 Line Code Violations, 8 Path Code Violations,
1 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 1149 Unavail Secs
E1 0/0/1 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20060707, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (665 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 665 Unavail Secs
Total Data (last 2 15 minute intervals):
2 Line Code Violations, 8 Path Code Violations,
1 Slip Secs, 1 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 1 Severely Err Secs, 1154 Unavail Secs

Mettendo il controller in “loopback diag” lo stato del controller e della Serial vanno UP e il DCE della Telecom va in allarme.

Router#sh controller E1
E1 0/0/0 is up. (Diagnostic Loopback)
Applique type is Channelized E1 - balanced
Receiver has no alarms.
alarm-trigger is not set
Version info Firmware: 20060707, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (844 seconds elapsed):
2 Line Code Violations, 0 Path Code Violations
1 Slip Secs, 1 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins
2 Errored Secs, 0 Bursty Err Secs, 1 Severely Err Secs, 762 Unavail Secs
Total Data (last 2 15 minute intervals):
2 Line Code Violations, 8 Path Code Violations,
1 Slip Secs, 0 Fr Loss Secs, 1 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 1149 Unavail Secs
E1 0/0/1 is down.
Applique type is Channelized E1 - balanced
Transmitter is sending remote alarm.
Receiver has loss of signal.
alarm-trigger is not set
Version info Firmware: 20060707, FPGA: 13, spm_count = 0
Framing is CRC4, Line Code is HDB3, Clock Source is Internal.
CRC Threshold is 320. Reported from firmware is 320.
Data in current interval (847 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 847 Unavail Secs
Total Data (last 2 15 minute intervals):
2 Line Code Violations, 8 Path Code Violations,
1 Slip Secs, 1 Fr Loss Secs, 2 Line Err Secs, 0 Degraded Mins,
2 Errored Secs, 0 Bursty Err Secs, 1 Severely Err Secs, 1154 Unavail Secs

Mi servirebbe una mano per capire che cosa sbaglio e come si configura questa interfaccia.
Grazie a tutti
Carlo