Problema Configurazione Router Cisco 877 per ADSL

Tutto ciò che ha a che fare con la configurazione di apparati Cisco (e non rientra nelle altre categorie)

Moderatore: Federico.Lagni

Rispondi
netuser2010
n00b
Messaggi: 6
Iscritto il: mer 15 dic , 2010 10:48 pm

Ciao a tutti,
avrei un problema sulla configurazione di un router cisco 877 per la mia adsl a 7Mb, infatti non riesco a navigare.
Il led PPP sul router è accesso quindi la negoziazione PPP la esegue, infatti l'ip mio pubblico lo riesco a pingare, ma oltre non vado.

Questa è la configurazione.

Codice: Seleziona tutto

!
hostname router
!
boot-start-marker
boot-end-marker
!
logging buffered 51200 warnings
!
no aaa new-model
!
resource policy
!
no ip source-route
ip cef
!
!
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool router
   default-router 10.10.10.1
   dns-server 62.94.0.1 62.94.0.2
   lease infinite
!
no ip domain lookup
ip name-server 62.94.0.1
ip name-server 62.94.0.2
!
crypto pki trustpoint TP-self-signed-3022873674
 enrollment selfsigned
 subject-name cn=IOS-Self-Signed-Certificate-3022873674
 revocation-check none
 rsakeypair TP-self-signed-3022873674
!
!
crypto pki certificate chain TP-self-signed-3022873674
 certificate self-signed 01 nvram:IOS-Self-Sig#3401.cer
username router
!
interface ATM0
 bandwidth 544
 no ip address
 no atm ilmi-keepalive
 pvc 8/35
  encapsulation aal5mux ppp dialer
  dialer pool-member 1
 !
 dsl operating-mode auto
 hold-queue 224 in
!
interface FastEthernet0
 no cdp enable
!
interface FastEthernet1
 no cdp enable
!
interface FastEthernet2
 no cdp enable
!
interface FastEthernet3
 no cdp enable
!
interface Vlan1
 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
 ip address 10.10.10.1 255.255.255.248
 ip nat inside
 ip virtual-reassembly
 ip tcp adjust-mss 1452
 hold-queue 100 out
!
interface Dialer0
 ip address negotiated
 ip nat outside
 ip virtual-reassembly
 encapsulation ppp
 dialer pool 1
 no cdp enable
 ppp chap hostname [email protected]
 ppp chap password 0 xxxxxxx
 ppp pap sent-username [email protected]  password 0 xxxxxx
!
ip route 0.0.0.0 0.0.0.0 Dialer0
!
!
ip http server
ip http access-class 23
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat translation timeout 420
ip nat translation tcp-timeout 120
ip nat translation pptp-timeout 420
ip nat translation icmp-timeout 1
ip nat translation max-entries 1000
ip nat inside source list nat interface Dialer0 overload
!
ip access-list extended nat
 permit ip 10.10.10.0 0.0.0.248 any
!
access-list 23 permit 10.10.10.0 0.0.0.7
no cdp run
!

control-plane

Grazie
paolomat75
Messianic Network master
Messaggi: 2965
Iscritto il: ven 29 gen , 2010 10:25 am
Località: Prov di GE

Ciao

Codice: Seleziona tutto

ip access-list extended nat
 permit ip 10.10.10.0 0.0.0.7 any 
poi dovrebbe andare
netuser2010
n00b
Messaggi: 6
Iscritto il: mer 15 dic , 2010 10:48 pm

paolomat75 ha scritto:Ciao

Codice: Seleziona tutto

ip access-list extended nat
 permit ip 10.10.10.0 0.0.0.7 any 
poi dovrebbe andare
Grazie mille ora funziona.

Un ultima cosa:
la mia adsl è a 7Mb ma effettuando lo speed test ottengo un valore 3,8 e 4.
Non vorrei che bisogna impostare qualcosa nella configurazione?

Grazie ancora
paolomat75
Messianic Network master
Messaggi: 2965
Iscritto il: ven 29 gen , 2010 10:25 am
Località: Prov di GE

Prego.
A quanto si sincronizza il router? Fai un

Codice: Seleziona tutto

show dsl int atm0
e posta il risultato.
netuser2010
n00b
Messaggi: 6
Iscritto il: mer 15 dic , 2010 10:48 pm

paolomat75 ha scritto:Prego.
A quanto si sincronizza il router? Fai un

Codice: Seleziona tutto

show dsl int atm0
e posta il risultato.
Scusa il ritardo.



router#show dsl int atm0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x03 0x1
Vendor ID: 'STMI' 'ALCB'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x0F 0x0F
Capacity Used: 100% 100%
Noise Margin: 10.5 dB 12.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 36.5 dB 22.0 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0xFF
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 8227 (0 spurious)
PHY Access Err: 0
Activations: 2
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-4.0.003.bin
Operation FW: AMR-4.0.003.bin
FW Version: 4.0.3

Interleave Fast Interleave Fast
Speed (kbps): 0 4800 0 512
Cells: 0 1621 0 95173
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 0 1
Header Errors: 0 0 0 0
Total BER: 0E-0 1154E-10
Leakage Avarage BER: 0E-0 1154E-10

LOM Monitoring : Disabled


DMT Bits Per Bin
000: 0 0 0 0 0 0 0 5 6 7 6 6 5 6 6 6
010: 6 6 7 7 7 7 8 7 7 7 7 8 7 8 0 0
020: 0 0 0 0 0 0 5 5 5 6 7 7 7 7 7 8
030: 8 8 8 7 8 8 8 8 8 8 8 8 8 8 8 8
040: 8 2 8 8 8 7 7 7 7 7 7 7 6 5 6 7
050: 6 7 6 6 6 6 6 6 4 4 4 6 6 6 6 6
060: 6 6 6 6 7 7 7 7 7 7 7 7 7 7 7 7
070: 7 6 6 6 4 4 5 4 4 4 6 6 6 6 7 7
080: 7 7 7 7 7 7 7 7 7 7 7 7 7 5 6 6
090: 7 6 5 4 3 2 5 5 5 5 6 5 6 6 6 6
0A0: 7 6 5 7 6 7 6 5 6 7 7 7 6 7 7 7
0B0: 7 6 7 7 5 6 5 6 6 6 6 7 6 7 6 6
0C0: 6 6 6 6 6 6 6 6 6 4 3 5 6 6 6 5
0D0: 6 6 6 6 6 6 6 6 6 6 5 6 6 6 6 6
0E0: 5 5 5 6 6 5 6 6 6 5 6 5 6 5 5 5
0F0: 5 5 5 5 5 5 5 5 5 4 4 4 4 4 4 4

DSL: Training log buffer capability is not enabled
paolomat75
Messianic Network master
Messaggi: 2965
Iscritto il: ven 29 gen , 2010 10:25 am
Località: Prov di GE

Allora. Il router si sincronizza a 4800 512 Kbps.
Perciò vai già bene. Hai la linea con Noise abbastanza alto.
Questo può dipendere da problemi della tua linea oppure sei distante dalla centrale.

Ciao
netuser2010
n00b
Messaggi: 6
Iscritto il: mer 15 dic , 2010 10:48 pm

paolomat75 ha scritto:Allora. Il router si sincronizza a 4800 512 Kbps.
Perciò vai già bene. Hai la linea con Noise abbastanza alto.
Questo può dipendere da problemi della tua linea oppure sei distante dalla centrale.

Ciao
OK.
Grazie mille.
Rispondi