Ciao bella gente, la situazione è questa:
Sede centrale più 11 sedi periferiche tutte in hdsl con una isdn di backup...
Per una di quelle il backup non vuole andare su...
Questa è la config del router periferico:
hostname Sined-Verona
!
boot-start-marker
boot-end-marker
!
enable secret 5 $1$5bLt$XqOkfv3V4cEMWrQPddd9C0
!
no aaa new-model
!
resource policy
!
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
ip cef
!
isdn switch-type basic-net3
!
username sined-re password 7 111A100B1216090F0F
!
interface FastEthernet0/0
ip address 192.168.13.254 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
duplex auto
speed auto
!
interface Serial0/0/0
description HDSL 2Mbps VERSO SEDE REGGIO EMILIA
bandwidth 2048
no ip address
encapsulation frame-relay IETF
no fair-queue
frame-relay lmi-type cisco
!
interface Serial0/0/0.1 point-to-point
bandwidth 2048
ip address 192.168.113.2 255.255.255.0
frame-relay interface-dlci 130
!
interface BRI0/1/0
description ISDN 0458781861
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
no cdp enable
ppp authentication chap
!
interface Dialer1
description DIALER INTERFACE PER BACKUP
ip address 192.168.213.2 255.255.255.0
encapsulation ppp
dialer pool 1
dialer remote-name sined-re
dialer idle-timeout 180
dialer string 0522326256
dialer string 0522294290
dialer hold-queue 50
dialer-group 1
no cdp enable
ppp authentication chap callin
ppp chap hostname Sined-Verona
ppp chap password 7 044802080A254E4D02
!
router eigrp 100
network 192.168.13.0
network 192.168.113.0
auto-summary
no eigrp log-neighbor-changes
!
ip local pool RAS 192.168.13.250 192.168.13.253
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.10.253
ip route 192.168.10.0 255.255.255.0 Dialer1 200
!
ip http server
no ip http secure-server
!
dialer-list 1 protocol ip permit
control-plane
line con 0
line aux 0
line vty 0 4
login local
!
end
Questa invece è quella del router centrale:
interface BRI1/0
description ISDN NT1+ # 0522-326256
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
ppp authentication chap
!
interface BRI1/1
description ISDN NT1+ # 0522-294290
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
ppp authentication chap callin
!
interface BRI1/2
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
!
interface BRI1/3
no ip address
isdn switch-type basic-net3
isdn point-to-point-setup
interface Dialer20
description INTERFACCIA DIALER PER BACKUP ISDN CON SINED VERONA
ip address 192.168.213.1 255.255.255.0
encapsulation ppp
dialer pool 1
dialer remote-name Sined-Verona
dialer idle-timeout 180
dialer string 0458781861
dialer-group 1
ppp authentication chap callin
ppp chap hostname sined-re
ppp chap password 7 111A100B1216090F0F
ip route 192.168.13.0 255.255.255.0 Dialer20 200
Backup ISDN che non va...
Moderatore: Federico.Lagni
-
Wizard
- Intergalactic subspace network admin
- Messaggi: 3441
- Iscritto il: ven 03 feb , 2006 10:04 am
- Località: Emilia Romagna
- Contatta:
-
Wizard
- Intergalactic subspace network admin
- Messaggi: 3441
- Iscritto il: ven 03 feb , 2006 10:04 am
- Località: Emilia Romagna
- Contatta:
Il comando backup...?!
Non basta la rotta staica?
Il problema è che se banalmente provo a pingare l' IP della punto-punto dell' altro router non va niente...
debug isdn events
debug ppp authentication
debug ppp negotiation
sined-re#ping 192.168.213.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.213.2, timeout is 2 seconds:
*May 17 02:43:13: ISDN BR1/0 EVENT: UserIdle: callid 0x8185 received ISDN_CALL (0x0)
*May 17 02:43:13: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1
*May 17 02:43:13: ISDN BR1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
*May 17 02:43:13: ISDN BR1/0 EVENT: service_queue_from_physical_layer: Recvd L1 prim 1 state is 0
*May 17 02:43:13: ISDN BR1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4.
*May 17 02:43:15: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 73 changed to up
*May 17 02:43:15: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_INFORMATION.
*May 17 02:43:17: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_PROCEEDING...
Success rate is 0 percent (0/5)
sined-re#
*May 17 02:43:22: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_DISCONNECT
*May 17 02:43:22: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_DISCONNECT_ACK
Non basta la rotta staica?
Il problema è che se banalmente provo a pingare l' IP della punto-punto dell' altro router non va niente...
debug isdn events
debug ppp authentication
debug ppp negotiation
sined-re#ping 192.168.213.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.213.2, timeout is 2 seconds:
*May 17 02:43:13: ISDN BR1/0 EVENT: UserIdle: callid 0x8185 received ISDN_CALL (0x0)
*May 17 02:43:13: ISDN BR1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1
*May 17 02:43:13: ISDN BR1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4
*May 17 02:43:13: ISDN BR1/0 EVENT: service_queue_from_physical_layer: Recvd L1 prim 1 state is 0
*May 17 02:43:13: ISDN BR1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4.
*May 17 02:43:15: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 73 changed to up
*May 17 02:43:15: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_INFORMATION.
*May 17 02:43:17: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_PROCEEDING...
Success rate is 0 percent (0/5)
sined-re#
*May 17 02:43:22: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_DISCONNECT
*May 17 02:43:22: ISDN BR1/0 EVENT: process_rxstate: ces/callid 1/0x8185 calltype 1 HOST_DISCONNECT_ACK
-
Wizard
- Intergalactic subspace network admin
- Messaggi: 3441
- Iscritto il: ven 03 feb , 2006 10:04 am
- Località: Emilia Romagna
- Contatta:
DALLA PARTE DELLA SEDE REMOTA:
Sined-Verona#ping 192.168.213.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.213.1, timeout is 2 seconds:
*Jul 19 12:48:25.707: ISDN BR0/1/0 EVENT: UserIdle: callid 0x8001 received ISDN_CALL (0x0)
*Jul 19 12:48:25.707: ISDN BR0/1/0 EVENT: process_bri_call: call id 0x8001, called_number 0522326256, Guid B41B25F48002 speed 64,
call type DATA, bchan -1 clng_num none
*Jul 19 12:48:25.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:25.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1
*Jul 19 12:48:25.711: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4.
*Jul 19 12:48:27.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:27.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0.
*Jul 19 12:48:29.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:29.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0.
*Jul 19 12:48:31.711: ISDN BR0/1/0 EVENT: process_rxstate: ces/callid 1/0x8001 calltype 1 HOST_DISCONNECT_ACK
*Jul 19 12:48:31.711: ISDN BR0/1/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8001.
*Jul 19 12:48:33.711: ISDN BR0/1/0 EVENT: isdn_layer1_failure: Layer 1 not active even after T3 delay
*Jul 19 12:48:33.711: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
*Jul 19 12:48:34.711: ISDN BR0/1/0 EVENT: UserIdle: callid 0x8002 received ISDN_CALL (0x0)
*Jul 19 12:48:34.711: ISDN BR0/1/0 EVENT: process_bri_call: call id 0x8002, called_number 0522294290, Guid B9790C9C8003 speed 64,
call type DATA, bchan -1 clng_num none
*Jul 19 12:48:34.715: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:34.715: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1.
Success rate is 0 percent (0/5)
Sined-Verona#
*Jul 19 12:48:36.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:36.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0
*Jul 19 12:48:38.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:38.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0
*Jul 19 12:48:40.711: ISDN BR0/1/0 EVENT: process_rxstate: ces/callid 1/0x8002 calltype 1 HOST_DISCONNECT_ACK
*Jul 19 12:48:40.711: ISDN BR0/1/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8002
*Jul 19 12:48:40.715: ISDN BR0/1/0 EVENT: service_queue_from_physical_layer: Recvd L1 prim ISDN_PH_DEACT_IND state is IF_ACTIVATIN
G
*Jul 19 12:48:40.715: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
*Jul 19 12:48:42.715: ISDN BR0/1/0 EVENT: isdn_layer1_failure: Layer 1 not active even after T3 delay
*Jul 19 12:48:42.715: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
Sined-Verona#
Sined-Verona#
Sined-Verona#sh isd
Sined-Verona#sh isdn st
Sined-Verona#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0/1/0 interface
dsl 2, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 2 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
DALLA PARTE CENTRALE:
sined-re#debug isdn events
debug isdn event is ON.
sined-re#debug ppp aut
sined-re#debug ppp authentication
PPP authentication debugging is on
sined-re#debug ppp neg
sined-re#debug ppp negotiation
PPP protocol negotiation debugging is on
sined-re#
sined-re#ter mon
sined-re#
sined-re#
sined-re#ping 192.168.213.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.213.2, timeout is 2 seconds:
*May 17 03:24:33: ISDN BR1/1 EVENT: UserIdle: callid 0x8188 received ISDN_CALL (0x0)
*May 17 03:24:33: ISDN BR1/1 EVENT: handle_l2d_srq_mail: Activating Layer 1
*May 17 03:24:33: ISDN BR1/1 EVENT: isdn_sw_cstate: State = 4, Old State = 4
*May 17 03:24:34: ISDN BR1/1 EVENT: service_queue_from_physical_layer: Recvd L1 prim 1 state is 0
*May 17 03:24:34: ISDN BR1/1 EVENT: isdn_sw_cstate: State = 4, Old State = 4.
*May 17 03:24:36: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/1, TEI 78 changed to up
*May 17 03:24:36: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_INFORMATION.
*May 17 03:24:37: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_PROCEEDING...
Success rate is 0 percent (0/5)
sined-re#
*May 17 03:24:42: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_DISCONNECT
*May 17 03:24:42: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_DISCONNECT_ACK
sined-re#
sined-re#
sined-re#sh isdn
sined-re#sh isdn st
sined-re#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 8 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/1 interface
dsl 9, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 78, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 9 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/2 interface
dsl 10, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 10 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/3 interface
dsl 11, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 11 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
Sined-Verona#ping 192.168.213.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.213.1, timeout is 2 seconds:
*Jul 19 12:48:25.707: ISDN BR0/1/0 EVENT: UserIdle: callid 0x8001 received ISDN_CALL (0x0)
*Jul 19 12:48:25.707: ISDN BR0/1/0 EVENT: process_bri_call: call id 0x8001, called_number 0522326256, Guid B41B25F48002 speed 64,
call type DATA, bchan -1 clng_num none
*Jul 19 12:48:25.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:25.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1
*Jul 19 12:48:25.711: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 4, Old State = 4.
*Jul 19 12:48:27.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:27.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0.
*Jul 19 12:48:29.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:29.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0.
*Jul 19 12:48:31.711: ISDN BR0/1/0 EVENT: process_rxstate: ces/callid 1/0x8001 calltype 1 HOST_DISCONNECT_ACK
*Jul 19 12:48:31.711: ISDN BR0/1/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8001.
*Jul 19 12:48:33.711: ISDN BR0/1/0 EVENT: isdn_layer1_failure: Layer 1 not active even after T3 delay
*Jul 19 12:48:33.711: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
*Jul 19 12:48:34.711: ISDN BR0/1/0 EVENT: UserIdle: callid 0x8002 received ISDN_CALL (0x0)
*Jul 19 12:48:34.711: ISDN BR0/1/0 EVENT: process_bri_call: call id 0x8002, called_number 0522294290, Guid B9790C9C8003 speed 64,
call type DATA, bchan -1 clng_num none
*Jul 19 12:48:34.715: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:34.715: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Activating Layer 1.
Success rate is 0 percent (0/5)
Sined-Verona#
*Jul 19 12:48:36.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:36.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0
*Jul 19 12:48:38.711: ISDN BR0/1/0 **ERROR**: handle_l2d_srq_mail: Layer 1 inactive
*Jul 19 12:48:38.711: ISDN BR0/1/0 EVENT: handle_l2d_srq_mail: Already activated Layer 1; status 0
*Jul 19 12:48:40.711: ISDN BR0/1/0 EVENT: process_rxstate: ces/callid 1/0x8002 calltype 1 HOST_DISCONNECT_ACK
*Jul 19 12:48:40.711: ISDN BR0/1/0 **ERROR**: host_disconnect_ack: Unfound B-channel on Disconnect_Ack call id 0x8002
*Jul 19 12:48:40.715: ISDN BR0/1/0 EVENT: service_queue_from_physical_layer: Recvd L1 prim ISDN_PH_DEACT_IND state is IF_ACTIVATIN
G
*Jul 19 12:48:40.715: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
*Jul 19 12:48:42.715: ISDN BR0/1/0 EVENT: isdn_layer1_failure: Layer 1 not active even after T3 delay
*Jul 19 12:48:42.715: ISDN BR0/1/0 EVENT: isdn_sw_cstate: State = 0, Old State = 4
Sined-Verona#
Sined-Verona#
Sined-Verona#sh isd
Sined-Verona#sh isdn st
Sined-Verona#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI0/1/0 interface
dsl 2, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 2 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
DALLA PARTE CENTRALE:
sined-re#debug isdn events
debug isdn event is ON.
sined-re#debug ppp aut
sined-re#debug ppp authentication
PPP authentication debugging is on
sined-re#debug ppp neg
sined-re#debug ppp negotiation
PPP protocol negotiation debugging is on
sined-re#
sined-re#ter mon
sined-re#
sined-re#
sined-re#ping 192.168.213.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.213.2, timeout is 2 seconds:
*May 17 03:24:33: ISDN BR1/1 EVENT: UserIdle: callid 0x8188 received ISDN_CALL (0x0)
*May 17 03:24:33: ISDN BR1/1 EVENT: handle_l2d_srq_mail: Activating Layer 1
*May 17 03:24:33: ISDN BR1/1 EVENT: isdn_sw_cstate: State = 4, Old State = 4
*May 17 03:24:34: ISDN BR1/1 EVENT: service_queue_from_physical_layer: Recvd L1 prim 1 state is 0
*May 17 03:24:34: ISDN BR1/1 EVENT: isdn_sw_cstate: State = 4, Old State = 4.
*May 17 03:24:36: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/1, TEI 78 changed to up
*May 17 03:24:36: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_INFORMATION.
*May 17 03:24:37: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_PROCEEDING...
Success rate is 0 percent (0/5)
sined-re#
*May 17 03:24:42: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_DISCONNECT
*May 17 03:24:42: ISDN BR1/1 EVENT: process_rxstate: ces/callid 1/0x8188 calltype 1 HOST_DISCONNECT_ACK
sined-re#
sined-re#
sined-re#sh isdn
sined-re#sh isdn st
sined-re#sh isdn status
Global ISDN Switchtype = basic-net3
ISDN BRI1/0 interface
dsl 8, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 8 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/1 interface
dsl 9, interface ISDN Switchtype = basic-net3
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 78, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 9 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/2 interface
dsl 10, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 10 CCBs = 0
The Free Channel Mask: 0x80000003
ISDN BRI1/3 interface
dsl 11, interface ISDN Switchtype = basic-net3
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 11 CCBs = 0
The Free Channel Mask: 0x80000003
Total Allocated ISDN CCBs = 0
-
Wizard
- Intergalactic subspace network admin
- Messaggi: 3441
- Iscritto il: ven 03 feb , 2006 10:04 am
- Località: Emilia Romagna
- Contatta:
A me sembra che ci siano dei problemi sulla borchia nella sede remota...
Voi che dite?
Voi che dite?
-
MaiO
- Messianic Network master
- Messaggi: 1083
- Iscritto il: sab 15 ott , 2005 10:55 am
- Località: Milano
- Contatta:
prova a fare un test dalla sede remota, effettua un call:
isdn test call interface bri 0/1/1:1 32805.....
dove 32805..... è il numero del tuo cellulare. Vedi se partono le chiamate, cosi escludi il problema borchia.
Ciao
isdn test call interface bri 0/1/1:1 32805.....
dove 32805..... è il numero del tuo cellulare. Vedi se partono le chiamate, cosi escludi il problema borchia.
Ciao
-=] MaiO [=-
-
Wizard
- Intergalactic subspace network admin
- Messaggi: 3441
- Iscritto il: ven 03 feb , 2006 10:04 am
- Località: Emilia Romagna
- Contatta:
Era uno schifosissimo cavo il problema...
Grazie a tutti per l' aiuto!
Grazie a tutti per l' aiuto!
-
zup
- Cisco fan
- Messaggi: 49
- Iscritto il: dom 21 dic , 2008 10:31 am
Scusa Wizard
alcune considerazione un pò retrodatate
Perchè nel dialer di Verona vengono specificati 2 numeri da chiamare (dialer string)
e perchè nel router centrale ci sono 2 interfacce Bri ad accettare un eventuale connessione da Verona
Questo significa che lato centrale hai solo 2 borchie ISDN che vengono utilizzate all' occorrenza dalle 11 sedi periferiche ?
Grazie
alcune considerazione un pò retrodatate
Perchè nel dialer di Verona vengono specificati 2 numeri da chiamare (dialer string)
e perchè nel router centrale ci sono 2 interfacce Bri ad accettare un eventuale connessione da Verona
Questo significa che lato centrale hai solo 2 borchie ISDN che vengono utilizzate all' occorrenza dalle 11 sedi periferiche ?
Grazie
