un saluto a tutti,vorrei alcune info ho acquistato due router isdn 1003 e 1603
ho sbattuto un pò la testa,con hyper terminal ma non ho ricavato un ragno dal buco,chi può darmi una configurazione già completa per questi router,ho isdn flat.
info (mod. "1003,1603 e isdn flat")
Moderatore: Federico.Lagni
-
TheIrish
- Site Admin
- Messaggi: 1840
- Iscritto il: dom 14 mar , 2004 11:26 pm
- Località: Udine
- Contatta:
Buondì,
lo dico per te, prima che qualche parola fuori posto esacerbi gli animi.
Qui, tipicamente, le richieste di configurazioni belle e fatte cadono nel vuoto. Praticamente nessuno risponde a post di questo tipo perché
1. ci sono un sacco di elementi specifici ad un network da considerare
2. non dimostra nemmeno il tentativo. Fa molto effetto helpdesk
3. partire da zero è scomodo. Se ci fosse una configurazione tentata, anche non funzionante, dalla quale partire, allora sarebbe diverso.
Bada, te lo faccio notare proprio perché un post del genere verrebbe ignorato, e sarebbe un peccato.
Piuttosto, cosa sai dei router cisco? Enable mode? Configuration mode? sai di cosa parlo?
lo dico per te, prima che qualche parola fuori posto esacerbi gli animi.
Qui, tipicamente, le richieste di configurazioni belle e fatte cadono nel vuoto. Praticamente nessuno risponde a post di questo tipo perché
1. ci sono un sacco di elementi specifici ad un network da considerare
2. non dimostra nemmeno il tentativo. Fa molto effetto helpdesk
3. partire da zero è scomodo. Se ci fosse una configurazione tentata, anche non funzionante, dalla quale partire, allora sarebbe diverso.
Bada, te lo faccio notare proprio perché un post del genere verrebbe ignorato, e sarebbe un peccato.
Piuttosto, cosa sai dei router cisco? Enable mode? Configuration mode? sai di cosa parlo?
-
noxar
- n00b
- Messaggi: 11
- Iscritto il: gio 01 feb , 2007 5:08 pm
Hai ragione forse mi sono espresso male chiedendo un pò troppo,inziamo di nuovo posto la config che mi dà con hyper terminal di tutte e due i cisco
questo è il 1600
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>#enable mode
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>#configure mode
Router>enter
Translating "enter"...domain server (255.255.255.255)
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
% Unknown command or computer name, or unable to find computer address
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory
program load complete, entry point: 0x4018060, size: 0x1e1568
%SYS-4-CONFIG_NEWER: Configurations from version 11.2 may not be correctly under
stood.
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Tr
complete, entry point: 0x8000060, size: 0x34c49c
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Image text-base: 0x0801CE4C, data-base: 0x02005000
cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of memory.
Processor board ID 11323426, with hardware revision 00000000
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface(s)
1 serial(sync/async) network interface(s)
System/IO memory with parity disabled
2048K bytes of DRAM onboard
System running from FLASH
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read ONLY)
Press RETURN to get started!
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
+++++++++++++++++++++++++
questo è il 1003
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>#enable mode
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>#configure mode
Router>enter
Translating "enter"...domain server (255.255.255.255)
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
% Unknown command or computer name, or unable to find computer address
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory
program load complete, entry point: 0x4018060, size: 0x1e1568
%SYS-4-CONFIG_NEWER: Configurations from version 11.2 may not be correctly under
stood.
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Tr
complete, entry point: 0x8000060, size: 0x34c49c
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Image text-base: 0x0801CE4C, data-base: 0x02005000
cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of memory.
Processor board ID 11323426, with hardware revision 00000000
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface(s)
1 serial(sync/async) network interface(s)
System/IO memory with parity disabled
2048K bytes of DRAM onboard
System running from FLASH
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read ONLY)
Press RETURN to get started!
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver prob
Router>config-if#int eth0
^
% Invalid input detected at '^' marker.
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>#enable
Router>#enable mode
Router>
%SYS-4-CONFIG_NEWER: Configurations from version 11.1 may not be correctly under
stood.
%QUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?program load comple
te, entry point: 0x2004000, size: 0x14cf59
Self decompressing the image : #################################################
## [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1000 Software (C1000-BNY-M), Version 11.1(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 05-Aug-96 10:52 by mkamson
Image text-base: 0x02004000, data-base: 0x022A9A14
cisco 1000 (68360) processor (revision D) with 7680K/512K bytes of memory.
Processor board ID 03287217
Bridging software.
Basic Rate ISDN software, Version 1.0.
1 Ethernet/IEEE 802.3 interface.
1 ISDN Basic Rate
8K bytes of non-volatile configuration memory.
2048K bytes of processor board PCMCIA flash (Read/Write)
Loading network-confg ... [timed out]
Loading cisconet.cfg ... [timed out]
Loading router-confg ... [timed out]
Loading ciscortr.cfg ... [timed out]
Press RETURN to get started!
%SYS-3-SUPNONE: Registry 0 doesn't exist
-Process= "Init", ipl= 4, pid= 1
-Traceback= 201BBD0 201C078 2283002 21ABE7A 21AB27C 21AB4C0 21AB538 2021D4C 2021
DB0 201867C 2018896
%LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, ch
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINK-3-UPDOWN: Interface BRI0, changed state to up
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up
%SYS-5-CONFIG_I: Configured from memory by console
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier.
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1000 Software (C1000-BNY-M), Version 11.1(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 05-Aug-96 10:52 by mkamson
Loading network-confg ...
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router> [timed out]
Loading cisconet.cfg config.
Translating "config"...domain server (255.255.255.255)..
% Unknown command or computer name, or unable to find computer address
Router>enabl [timed out]
Loading router-confg.
Translating "eg"...domain server (255.255.255.255) [timed out]
Loading ciscortr.cfg .
% Unknown command or computer name, or unable to find computer address
Router>enab.le
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?.ok
Translating "enableok"...domain server (255.255.255.255) [timed out]
% Unknown command or computer name, or unable to find computer address
Router>enable
Password:
Password:
Password:
% Bad secrets
Router>enable
Password:
Password:
Password:
% Bad secrets
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>#config
Router>#confg
Router>
++++++++++++++++++++
e qui mi son o fermato non ho trovato un doc dettagliato per creare una nuova configurazione,vorrei fare prima un reset e poi iniziare,qualche suggerimento grazie
questo è il 1600
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>#enable mode
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>#configure mode
Router>enter
Translating "enter"...domain server (255.255.255.255)
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
% Unknown command or computer name, or unable to find computer address
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory
program load complete, entry point: 0x4018060, size: 0x1e1568
%SYS-4-CONFIG_NEWER: Configurations from version 11.2 may not be correctly under
stood.
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Tr
complete, entry point: 0x8000060, size: 0x34c49c
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Image text-base: 0x0801CE4C, data-base: 0x02005000
cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of memory.
Processor board ID 11323426, with hardware revision 00000000
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface(s)
1 serial(sync/async) network interface(s)
System/IO memory with parity disabled
2048K bytes of DRAM onboard
System running from FLASH
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read ONLY)
Press RETURN to get started!
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
+++++++++++++++++++++++++
questo è il 1003
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>#enable mode
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>#configure mode
Router>enter
Translating "enter"...domain server (255.255.255.255)
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
% Unknown command or computer name, or unable to find computer address
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
System Bootstrap, Version 11.1(10)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1997 by cisco Systems, Inc.
C1600 processor with 2048 Kbytes of main memory
program load complete, entry point: 0x4018060, size: 0x1e1568
%SYS-4-CONFIG_NEWER: Configurations from version 11.2 may not be correctly under
stood.
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Tr
complete, entry point: 0x8000060, size: 0x34c49c
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
Image text-base: 0x0801CE4C, data-base: 0x02005000
cisco 1601 (68360) processor (revision C) with 1536K/512K bytes of memory.
Processor board ID 11323426, with hardware revision 00000000
Bridging software.
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
1 Ethernet/IEEE 802.3 interface(s)
1 serial(sync/async) network interface(s)
System/IO memory with parity disabled
2048K bytes of DRAM onboard
System running from FLASH
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read ONLY)
Press RETURN to get started!
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%SYS-5-CONFIG_I: Configured from memory by console
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-Y-L), Version 11.2(12)P, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Tue 03-Mar-98 06:29 by dschwart
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver prob
Router>config-if#int eth0
^
% Invalid input detected at '^' marker.
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>#enable
Router>#enable mode
Router>
%SYS-4-CONFIG_NEWER: Configurations from version 11.1 may not be correctly under
stood.
%QUICC-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?program load comple
te, entry point: 0x2004000, size: 0x14cf59
Self decompressing the image : #################################################
## [OK]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) 1000 Software (C1000-BNY-M), Version 11.1(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 05-Aug-96 10:52 by mkamson
Image text-base: 0x02004000, data-base: 0x022A9A14
cisco 1000 (68360) processor (revision D) with 7680K/512K bytes of memory.
Processor board ID 03287217
Bridging software.
Basic Rate ISDN software, Version 1.0.
1 Ethernet/IEEE 802.3 interface.
1 ISDN Basic Rate
8K bytes of non-volatile configuration memory.
2048K bytes of processor board PCMCIA flash (Read/Write)
Loading network-confg ... [timed out]
Loading cisconet.cfg ... [timed out]
Loading router-confg ... [timed out]
Loading ciscortr.cfg ... [timed out]
Press RETURN to get started!
%SYS-3-SUPNONE: Registry 0 doesn't exist
-Process= "Init", ipl= 4, pid= 1
-Traceback= 201BBD0 201C078 2283002 21ABE7A 21AB27C 21AB4C0 21AB538 2021D4C 2021
DB0 201867C 2018896
%LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0, ch
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%LINK-3-UPDOWN: Interface BRI0, changed state to up
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to up
%SYS-5-CONFIG_I: Configured from memory by console
%LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed state to down
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier.
%SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) 1000 Software (C1000-BNY-M), Version 11.1(5), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1996 by cisco Systems, Inc.
Compiled Mon 05-Aug-96 10:52 by mkamson
Loading network-confg ...
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router> [timed out]
Loading cisconet.cfg config.
Translating "config"...domain server (255.255.255.255)..
% Unknown command or computer name, or unable to find computer address
Router>enabl [timed out]
Loading router-confg.
Translating "eg"...domain server (255.255.255.255) [timed out]
Loading ciscortr.cfg .
% Unknown command or computer name, or unable to find computer address
Router>enab.le
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?.ok
Translating "enableok"...domain server (255.255.255.255) [timed out]
% Unknown command or computer name, or unable to find computer address
Router>enable
Password:
Password:
Password:
% Bad secrets
Router>enable
Password:
Password:
Password:
% Bad secrets
Router>
%QUICC_ETHER-1-LOSTCARR: Unit 0, lost carrier. Transceiver problem?
Router>enable mode
^
% Invalid input detected at '^' marker.
Router>#config
Router>#confg
Router>
++++++++++++++++++++
e qui mi son o fermato non ho trovato un doc dettagliato per creare una nuova configurazione,vorrei fare prima un reset e poi iniziare,qualche suggerimento grazie
saluti by noxar
-
noxar
- n00b
- Messaggi: 11
- Iscritto il: gio 01 feb , 2007 5:08 pm
posto un pò di comandi che gli ho dato
show int
show isdn status
debug isdn q921
debug isdn q931
debug ppp negotiation
debug ppp authentication
*******************************
Router>show int
BRI0 is up, line protocol is down
Hardware is BRI
Internet address is 192.168.2.1/24
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/64/0 (size/threshold/drops)
Conversations 0/0 (active/max active)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 1 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Router>show isdn status
The current ISDN Switchtype = basic-ni1
ISDN BRI0 interface
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
No Active Layer 3 Call(s)
Activated dsl 0 CCBs = 0
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++€
invece questi comandi non mi dà niente
debug isdn q921
debug isdn q931
debug ppp negotiation
debug ppp authentication
show int
show isdn status
debug isdn q921
debug isdn q931
debug ppp negotiation
debug ppp authentication
*******************************
Router>show int
BRI0 is up, line protocol is down
Hardware is BRI
Internet address is 192.168.2.1/24
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/64/0 (size/threshold/drops)
Conversations 0/0 (active/max active)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 1 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Router>show isdn status
The current ISDN Switchtype = basic-ni1
ISDN BRI0 interface
Layer 1 Status:
DEACTIVATED
Layer 2 Status:
Layer 2 NOT Activated
Layer 3 Status:
No Active Layer 3 Call(s)
Activated dsl 0 CCBs = 0
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++€
invece questi comandi non mi dà niente
debug isdn q921
debug isdn q931
debug ppp negotiation
debug ppp authentication
saluti by noxar
-
TheIrish
- Site Admin
- Messaggi: 1840
- Iscritto il: dom 14 mar , 2004 11:26 pm
- Località: Udine
- Contatta:
Per la pass recovery, guarda qui: http://www.areanetworking.it/index_docs ... uter_Cisco
per il resto, posta una show run.
per il resto, posta una show run.
-
noxar
- n00b
- Messaggi: 11
- Iscritto il: gio 01 feb , 2007 5:08 pm
que e quello che mi dà show run sul modello 1600
Current configuration:
!
version 11.2
no service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname Router
!
!
!
interface Ethernet0
no ip address
shutdown
!
interface Serial0
no ip address
shutdown
!
no ip classless
!
line con 0
--More--
Current configuration:
!
version 11.2
no service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname Router
!
!
!
interface Ethernet0
no ip address
shutdown
!
interface Serial0
no ip address
shutdown
!
no ip classless
!
line con 0
--More--
saluti by noxar
-
noxar
- n00b
- Messaggi: 11
- Iscritto il: gio 01 feb , 2007 5:08 pm
questo e il show run del 1003
Current configuration:
!
version 11.1
service config
service slave-log
no service pad
service udp-small-servers
service tcp-small-servers
!
hostname Router
!
enable secret 5 $1$W6K7$1zkpBniYFMVfZpMbv1TFj/
enable password cisco1003
!
isdn switch-type basic-ni1
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
shutdown
!
interface BRI0
ip address 192.168.2.1 255.255.255.0
--More--
Current configuration:
!
version 11.1
service config
service slave-log
no service pad
service udp-small-servers
service tcp-small-servers
!
hostname Router
!
enable secret 5 $1$W6K7$1zkpBniYFMVfZpMbv1TFj/
enable password cisco1003
!
isdn switch-type basic-ni1
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
shutdown
!
interface BRI0
ip address 192.168.2.1 255.255.255.0
--More--
saluti by noxar
-
TheIrish
- Site Admin
- Messaggi: 1840
- Iscritto il: dom 14 mar , 2004 11:26 pm
- Località: Udine
- Contatta:
Grazie per il primo pezzo della configurazione... saremmo più lieti di vedere anche il resto.
-
noxar
- n00b
- Messaggi: 11
- Iscritto il: gio 01 feb , 2007 5:08 pm
iao TheIrish,non sono tanto pratico se saprei quali comandi dargli l'avrei già configurato,se qualcuno vuole farmi da assistenza remota e mi dà una mano. Posto i due comanid shiw run e show interface
Router#show interface
BRI0 is administratively down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/64/0 (size/threshold/drops)
Conversations 0/0 (active/max active)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 1 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Ethernet0 is administratively down, line protocol is down
Hardware is QUICC Ethernet, address is 0060.7061.fb27 (bia 0060.7061.fb27)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 231/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:04:25, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
10 packets output, 600 bytes, 0 underruns
10 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
10 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
show run
Current configuration:
!
version 11.1
service slave-log
no service pad
service udp-small-servers
service tcp-small-servers
!
hostname Router
!
!
!
interface Ethernet0
no ip address
shutdown
!
interface BRI0
no ip address
shutdown
!
no ip classless
!
line con 0
line vty 0 4
login
!
end
Router#show interface
BRI0 is administratively down, line protocol is down
Hardware is BRI
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec, rely 255/255, load 1/255
Encapsulation HDLC, loopback not set
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0 (size/max/drops); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/64/0 (size/threshold/drops)
Conversations 0/0 (active/max active)
Reserved Conversations 0/0 (allocated/max allocated)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 1 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
Ethernet0 is administratively down, line protocol is down
Hardware is QUICC Ethernet, address is 0060.7061.fb27 (bia 0060.7061.fb27)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 231/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:04:25, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
10 packets output, 600 bytes, 0 underruns
10 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
10 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
show run
Current configuration:
!
version 11.1
service slave-log
no service pad
service udp-small-servers
service tcp-small-servers
!
hostname Router
!
!
!
interface Ethernet0
no ip address
shutdown
!
interface BRI0
no ip address
shutdown
!
no ip classless
!
line con 0
line vty 0 4
login
!
end
saluti by noxar
-
TheIrish
- Site Admin
- Messaggi: 1840
- Iscritto il: dom 14 mar , 2004 11:26 pm
- Località: Udine
- Contatta:
Qui si cerca di risolvere i problemi, non si fa scuola.
Quella che hai postato non è un tentativo di configurazione, è un router resettato e appena acceso. Non hai letto, non ti sei informato, non ci hai nemmeno provato.
Se questa è una cosa che non VUOI fare (se tu lo volessi fare, ti saresti documentato), fai qualcos'altro.
Quella che hai postato non è un tentativo di configurazione, è un router resettato e appena acceso. Non hai letto, non ti sei informato, non ci hai nemmeno provato.
Se questa è una cosa che non VUOI fare (se tu lo volessi fare, ti saresti documentato), fai qualcos'altro.
