Ho pensato di provare con uno show dsl int atm0, ecco i risultati.. un rapporto segnale/rumore di 40dB non è male, vero? la linea non dovrebbe fare schifo, anche se sono costretto ad usare un cavo telefonico da una 20ina di metri..
PS cosa vuol dire Last Fail Code: Protocol error ??
Codice: Seleziona tutto
Router#show dsl int atm0
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ANSI T1.413
ANSI Issue/rev: 2/1 2/1
Vendor ID: 0x0022 0x4D54
Capacity Used: 11% 36%
Noise Margin: 39.5 dB 30.0 dB
Output Power: 20.0 dBm 11.5 dBm
Attenuation: 19.0 dB 10.0 dB
Defect Status: None None
Last Fail Code: Protocol error
Selftest Result: 0x49
Subfunction: 0x02
Interrupts: 649 (1 spurious)
Activations: 1
SW Version: 3.8129
FW Version: 0x1A04
Interleave Fast Interleave Fast
Speed (kbps): 800 0 320 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 7 0
Header Errors: 0 0 2 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0
DMT Bits Per Bin
00: 0 0 0 0 0 0 0 0 0 2 3 4 4 5 5 6
10: 6 6 6 6 6 6 6 5 5 5 5 4 4 4 0 0
20: 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2
30: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
40: 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
50: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
60: 2 3 2 2 2 2 2 2 2 2 2 2 2 2 2 2
70: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
80: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
90: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
A0: 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
B0: 2 2 0 2 2 0 0 2 2 2 2 2 0 0 0 0
C0: 0 0 0 0 0 2 0 0 0 0 0 0 0 0 0 0
D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Training log buffer capability is not enabled yet.