JosephFalck ha scritto:La configurazione la prende. Solo che non mi da segni di vita. Con i vari comandi vedo tutte le interface in up. Che può essere?
puoi postare i comandi che ti ho suggerito sia qui che in MP?
Moderatore: Federico.Lagni
JosephFalck ha scritto:La configurazione la prende. Solo che non mi da segni di vita. Con i vari comandi vedo tutte le interface in up. Che può essere?
Codice: Seleziona tutto
How to load a config file onto a Cisco router
Plug the blue serial cable [known as a console cable] that came with your Cisco router into the console port on the router and the serial port in your computer. Start up your favourite terminal program (such as HyperTerminal - select "Direct to COMx"). The correct terminal settings are 9600 baud, 8 data bits, no parity, 1 stop bit, and I usually choose hardware flow control. For reliability, you also need to set the line delay to 100ms (File/Properties/Settings/ASCII Setup).
If the router is on, switch it off. Now turn the router on. Note that it takes about two minutes for router to complete booting. If the router asks if you want to run the setup wizard, say no. If it asks you if you want to get started tap return a couple of times. If you get nothing within 30 seconds of turning the router on, tap return a few times. If you still get nothing then check your serial connections and parameters.
For safety, lets start by wiping the routers current config. Enter these commands:
enable
erase nvram:
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
Press "y" to erase the routers config. Then enter the below commands. Note that the router may not ask you to save the current config. If it does, make sure you say no - we are trying to wipe the config.
reload
System configuration has been modified. Save? [yes/no]: no
Proceed with reload? [confirm]
Press "y" to let the router reboot. For those people who have some familiarity with Cisco routers the "erase nvram:" command has supersede the "write erase" and "erase startup-config" commands (these commands all do the same thing).
When the router has completed booting this time it will ask if you want to run the setup wizard, say "no".
It should eventually tell you to press "return to get started".
Tap return a few times.
Now we need to go into config mode:
enable
config terminal
Now copy the config you want to load onto the router into the clipboard (hint: CTRL-A then CTRL-C), and paste into HyperTerminal (Edit/Paste To Host). Once it has pasted in, you need to save the config.
CTRL-Z
copy running-config startup-config
Codice: Seleziona tutto
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES unset up down
FastEthernet1 unassigned YES unset up down
FastEthernet2 unassigned YES unset up down
FastEthernet3 unassigned YES unset up down
ATM0 unassigned YES NVRAM up up
ATM0.1 unassigned YES unset up up
Vlan1 unassigned YES NVRAM up down
NVI0 unassigned YES unset administratively down down
Dialer0 unassigned YES NVRAM up up
BVI1 192.168.0.221 YES NVRAM down down
Virtual-Access1 unassigned YES unset down down
Codice: Seleziona tutto
show int atm0
ATM0 is up, line protocol is up
Hardware is MPC ATMSAR (with Alcatel ADSL Module)
MTU 4470 bytes, sub MTU 4470, BW 640 Kbit/sec, DLY 570 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 1024 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
160 packets input, 9344 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
160 packets output, 11888 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Codice: Seleziona tutto
sh dsl int
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x03 0x2
Vendor ID: 'STMI' 'P '
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x0F 0xB5
Chip ID: C196 (0)
DFE BOM: DFE3.0 Annex A (1)
Capacity Used: 98% 78%
Noise Margin: 11.5 dB 18.0 dB
Output Power: 20.0 dBm 12.5 dBm
Attenuation: 21.0 dB 11.5 dB
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x9A
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 8255 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-3.0.014_no_bist.bin
Operation FW: AMR-3.0.014.bin
FW Source: embedded
FW Version: 3.0.14
Interleave Fast Interleave Fast
Speed (kbps): 7008 0 640 0
Cells: 332 0 573948 0
Reed-Solomon EC: 0 0 0 0
CRC Errors: 0 0 1 0
Header Errors: 0 0 0 0
Total BER: 0E-0 0E-0
Leakage Average BER: 0E-0 0E-0
ATU-R (DS) ATU-C (US)
Bitswap: enabled enabled
Bitswap success: 0 0
Bitswap failure: 0 0
LOM Monitoring : Disabled
DMT Bits Per Bin
000: 0 0 0 0 0 0 2 4 7 7 9 9 A A A A
010: A A A 9 9 9 9 9 8 8 7 6 5 4 2 0
020: 0 0 0 0 0 A B B B B B B C C B B
030: B B C B B B B B B B B B B B B B
040: 0 B B B A B B B A A B B B B B B
050: A 2 A A A A A A A A A A A A A A
060: A A A A A A A A A A A A A A A A
070: A A A A A 9 A 9 A A 9 9 9 9 9 A
080: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
090: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9
0A0: 9 9 9 9 9 9 9 9 9 9 9 8 8 9 8 9
0B0: 9 9 9 8 9 9 9 9 9 9 9 9 9 8 8 9
0C0: 9 8 8 9 8 8 8 8 8 8 8 8 8 8 8 8
0D0: 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8
0E0: 8 8 8 8 8 8 8 8 8 8 8 7 8 7 8 8
0F0: 7 8 7 8 7 7 8 7 7 7 8 8 8 8 8 8
DSL: Training log buffer capability is not enabled
Crea un topic dedicato con la tua attuale config, vedremo di correggerla insiemeio ho un router Cisco 877W e la suddetta connessione ma non sono ancora riuscito a configurarlo
=========================================================@lan72 ha scritto:Salve a tutti, tenevo a farvi sapere che sono molto riconoscente nei confronti di questo forum perchè ho trovato persone capaci e allo stesso molto disponibili, considerando che i cisco per chi partiva da 0 come me sono praticamente impossibili, qui ho avuto la possibilità in poco tempo di imparare quanto basta per poterne configurare uno.
ps. un ringraziamento particolare va a Wizard..
Volevo contribuire allegando la mia configurazione per Cisco 857W funzionante al 100% con:
Alice 20 Mega (casa ip dinamico)
Dhcp Server
DynDns
Wifi con Wpa2
Filtro MAC WiFi
Firewall
Ntp Update
il range del hdcp è dal 192.168.0.1 al 192.168.0.220
l'indirizzo del router è 192.168.0.221
per semplificare il tutto, ho predisposto dei campi caratterizzati da parentesi quadra dove allinterno deve essere inserito il valore desiderato
Codice: Seleziona tutto
no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname [NOME-ROUTER] ! boot-start-marker boot-end-marker ! logging buffered 52000 enable secret 5 [SECRET-PASSWORD] ! no aaa new-model clock timezone MET 1 clock summer-time MEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 ! dot11 association mac-list 700 dot11 syslog dot11 vlan-name WiFi vlan 1 ! dot11 ssid [NOME-SSID] vlan 1 authentication open authentication key-management wpa guest-mode wpa-psk ascii 7 [PASSWORD-WIFI-MASSIMO-63-CARATTERI] ! no ip dhcp use vrf connected ip dhcp excluded-address 192.168.0.221 192.168.0.254 ! ip dhcp pool Pool1 import all network 192.168.0.0 255.255.255.0 default-router 192.168.0.221 dns-server [1-DNS-X-CLIENT] [2-DNS-x-CLIENT] lease infinite ! ! ip cef ip inspect log drop-pkt ip inspect name Firewall cuseeme ip inspect name Firewall dns ip inspect name Firewall ftp ip inspect name Firewall h323 ip inspect name Firewall https ip inspect name Firewall icmp ip inspect name Firewall imap ip inspect name Firewall pop3 ip inspect name Firewall rcmd ip inspect name Firewall realaudio ip inspect name Firewall rtsp ip inspect name Firewall esmtp ip inspect name Firewall sqlnet ip inspect name Firewall streamworks ip inspect name Firewall tftp ip inspect name Firewall tcp ip inspect name Firewall udp ip inspect name Firewall vdolive ip auth-proxy max-nodata-conns 3 ip admission max-nodata-conns 3 ip domain name cisco.com ip name-server [1-DNS-RISOLUXIONE-NOMI-X-ROUTER] ip name-server [2-DNS-RISOLUXIONE-NOMI-X-ROUTER] ip ddns update method dyndns1 HTTP add http://[NOMEUTENTE]:[PASSWORD]@members.dyndns.org/nic/update?system=dyndns&ho stname=<h>&myip=<a> remove http://[NOMEUTENTE]:[PASSWORD]@members.dyndns.org/nic/update?system=dyndns &hostname=<h>&myip=<a> ! ! username [NOME-UTENTE-ACCESSO-ROUTER] privilege 15 secret 5 [PASSWORD] ! ! archive log config hidekeys ! ! ! bridge irb ! ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode adsl2+ ! interface ATM0.1 point-to-point pvc 8/35 pppoe-client dial-pool-number 1 ! ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address ! encryption vlan 1 mode ciphers aes-ccm tkip ! ssid [NOME-SSID-WIFI] ! speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 b asic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 station-role root world-mode dot11d country IT both l2-filter bridge-group-acl ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Vlan1 no ip address ip tcp adjust-mss 1452 bridge-group 1 ! interface Dialer0 ip ddns update hostname [HOST-DYNDNS].gotdns.com ip ddns update dyndns1 ip address negotiated ip access-group 101 in ip mtu 1492 ip inspect Firewall out ip nat outside ip virtual-reassembly encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication pap callin ppp pap sent-username [UTENTE]@alice.it password 7 [PASSWORD] ! interface BVI1 ip address 192.168.0.221 255.255.255.0 ip access-group 102 in ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452 ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 Dialer0 ! ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface Dialer0 overload ! access-list 1 permit 192.168.0.0 0.0.0.255 access-list 101 remark Traffico abilitato ad entrare nel router da internet access-list 101 deny ip 0.0.0.0 0.255.255.255 any access-list 101 deny ip 10.0.0.0 0.255.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 169.254.0.0 0.0.255.255 any access-list 101 deny ip 172.16.0.0 0.15.255.255 any access-list 101 deny ip 192.0.2.0 0.0.0.255 any access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 198.18.0.0 0.1.255.255 any access-list 101 deny ip 224.0.0.0 0.15.255.255 any access-list 101 deny ip any host 255.255.255.255 access-list 101 permit udp host [1-DNS-RISOLUXIONE-NOMI-X-ROUTER] eq domain any access-list 101 permit udp host [2-DNS-RISOLUXIONE-NOMI-X-ROUTER] eq domain any access-list 101 permit tcp host 63.208.196.96 eq www any log access-list 101 permit udp host 207.46.232.42 eq ntp any access-list 101 permit udp host 192.43.244.18 eq ntp any access-list 101 permit gre any any access-list 101 deny icmp any any echo access-list 101 deny ip any any log access-list 102 remark Traffico abilitato ad entrare nel router dalla ethernet access-list 102 permit ip any host 192.168.0.221 access-list 102 deny ip any host 192.168.0.255 access-list 102 deny udp any any eq tftp log access-list 102 deny ip any 0.0.0.0 0.255.255.255 log access-list 102 deny ip any 10.0.0.0 0.255.255.255 log access-list 102 deny ip any 127.0.0.0 0.255.255.255 log access-list 102 deny ip any 169.254.0.0 0.0.255.255 log access-list 102 deny ip any 172.16.0.0 0.15.255.255 log access-list 102 deny ip any 192.0.2.0 0.0.0.255 log access-list 102 deny ip any 192.168.0.0 0.0.255.255 log access-list 102 deny ip any 198.18.0.0 0.1.255.255 log access-list 102 deny udp any any eq 135 log access-list 102 deny tcp any any eq 135 log access-list 102 deny udp any any eq netbios-ns log access-list 102 deny udp any any eq netbios-dgm log access-list 102 deny tcp any any eq 445 log access-list 102 permit ip 192.168.0.0 0.0.0.255 any access-list 102 permit ip any host 255.255.255.255 access-list 102 deny ip any any log access-list 700 permit [MAC-ADDRESS-WIFI-ABILITATI] (Esempio 0015.1181.a949 0000.0000.0000) access-list 700 deny 0000.0000.0000 ffff.ffff.ffff dialer-list 1 protocol ip permit no cdp run ! control-plane ! bridge 1 protocol ieee bridge 1 route ip banner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C ! line con 0 login local no modem enable line aux 0 line vty 0 4 privilege level 15 login local transport input telnet ssh ! scheduler max-task-time 5000 sntp server 207.46.197.32 sntp server 192.43.244.18 end
Spero di aver fatto cosa gradita...
Saluti
Agostino