non è proprio semplicissimo ( nulla di trascendentale cmq ). devi seguire una determinata procedura, qui ti posto quello che è l'inizio di un manuale in italiano che stavo facendo ma mai finito :
estrapola quello che ti serve e se manca qualcosa cerca in google è da li che ai tempi ho trovato tutto, ci vuole un pò di pazienza iniziale.
ciao
-----------------------------------------------------------------------------
Scaricare i file necessari all’installazione del Cisco Unity Express(
http://www.cisco.com/kobayashi/sw-center/sw-voice.shtml ):
– cue-installer.2.0.1 (Helper installer)
– cue-vm-installer.2.0.1.prt1 (installer payload file)
– cue-vm.2.0.1.pkg (main software package file)
– cue-vm-full.2.0.1.prt1 (voicemail application)
– cue-vm-lang-pack.2.0.1.pkg (language package file)
– cue-vm-language-pack.2.0.1.prt1 (language prompts)
Copiare il cue-installer.2.0.1 nel TFTP server, tutti gli altri file nell’FTP server.
You must configure several parameters in the CUE server to be able to download the CUE software files.
SUMMARY STEPS
1. reload
2. Type "***" to go into the boot loader mode.
3. config
4. Enter the values for the following parameters:
– Network module's IP address
– Subnet mask
– TFTP server address
– Gateway router address
– Ethernet interface is internal
– Default helper image is cue-installer.2.0.1
– Default boot setting
– Default bootloader is secondary
5. Boot the NM with the boot helper.
DETAILED STEPS
________________________________________
Step 1 Type reload to restart the system.
Step 2 Type "***" to go into the boot loader mode.
Step 3 Type config to go into configuration mode.
Step 4 Enter the values for the following parameters:
• Network module's IP address
• Subnet mask
• TFTP server address
• Gateway router address
• Ethernet interface: internal
• Default helper image: cue-installer.2.0.1
• Default boot: disk
• Default bootloader: secondary
Step 5 Type boot helper to begin the installation. This will load the installer
________________________________________
What to Do Next
Install the software files. See "Installing the Software Image Files".
Installing the Software Image Files
After downloading the software files and backing up your data, you are ready to install the software image files.
Prerequisites
Installing the software image files requires the following information:
• TFTP server IP address
• FTP server IP address
• FTP server user ID
• FTP server password
• Software package name
________________________________________
Note Back up current system configurations and data before installing new software.
________________________________________
SUMMARY STEPS
Starting from NM EXEC mode:
1. Select the first choice, Install Software, from the install menu.
2. Enter the package name, FTP server address, username, and password.
3. Select the language version from the language selection menu.
4. Enter x when finished with the language selection menu.
5. Enter y to begin the initial configuration in the post installation configuration menu.
6. Enter y to restore the configuration saved in flash memory or n to use your backup to restore your configuration.
7. Enter the CUE administrator ID. This is the username to log in to the CUE GUI.
DETAILED STEPS
________________________________________
Step 1 Select the first choice, Install Software, from the install menu:
Welcome to Cisco Systems Service Engine Helper Software
Please select from the following
1 Install software
2 Reload module
(Type '?' at any time for help)
Choice: 1
Step 2 Enter the package name, FTP server address, username, and password:
Package name: cue-vm.2.0.1.pkg
Server url:
ftp://192.168.1.3/
Username: cue
Password: ******
Software installation will clear disk contents
Continue [y/n]? y
________________________________________
Caution This step cleans the disk. All configuration and voice messages will be lost after this step. For future upgrades and installations, verify that a backup has been done. If it has not, abort at this step and do a backup first.
________________________________________
Step 3 Select the language version from the language selection menu:
Language Selection Menu:
Num. Selected Installed Language Name
-------------------------------------------
1 FRA CUE Voicemail European French (2.0.0)
2 ESP CUE Voicemail European Spanish (2.0.0)
3 DEU CUE Voicemail German (2.0.0)
4 ENG CUE Voicemail US English (2.0.0)
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
>4
Step 4 Your choice will appear as a "*" in the language selection menu. Use the menu to add, remove, or get information about languages. Enter x when finished.
Language Selection Menu:
Num. Selected Installed Language Name
-------------------------------------------
1 FRA CUE Voicemail European French (2.0.0)
2 ESP CUE Voicemail European Spanish (2.0.0)
3 DEU CUE Voicemail German (2.0.0)
4 * ENG CUE Voicemail US English (2.0.0)
Available commands are:
# - enter the number for the language to select one
r # - remove the language for given #
i # - more information about the language for given #
x - Done with language selection
>x
Step 5 Enter y to begin the initial configuration:
IMPORTANT::
IMPORTANT:: Welcome to Cisco Systems Service Engine
IMPORTANT:: post installation configuration tool.
IMPORTANT::
IMPORTANT:: This is a one time process which will guide
IMPORTANT:: you through initial setup of your Service Engine.
IMPORTANT:: Once run, this process will have configured
IMPORTANT:: the system for your location.
IMPORTANT::
IMPORTANT:: If you do not wish to continue, the system will be halted
IMPORTANT:: so it can be safely removed from the router.
IMPORTANT::
Do you wish to start configuration now (y,n)? y
Step 6 Enter the appropriate response y or n. See the output below to determine your configuration needs.
IMPORTANT::
IMPORTANT:: A Cisco Unity Express configuration has been found in flash.
IMPORTANT:: You can choose to restore this configuration into the
IMPORTANT:: current image.
IMPORTANT::
IMPORTANT:: A stored configuration contains some of the data from a
IMPORTANT:: previous installation, but not as much as a backup. For
IMPORTANT:: example: voice messages, user passwords, user PINs, and
IMPORTANT:: auto attendant scripts are included in a backup, but are
IMPORTANT:: not saved with the configuration.
IMPORTANT::
IMPORTANT:: If you are recovering from a disaster and do not have a
IMPORTANT:: backup, you can restore the saved configuration.
IMPORTANT::
IMPORTANT:: If you are going to restore a backup from a previous
IMPORTANT:: installation, you should not restore the saved configuration.
IMPORTANT::
IMPORTANT:: If you choose not to restore the saved configuration, it
IMPORTANT:: will be erased from flash.
IMPORTANT::
Would you like to restore the saved configuration? (y,n)
Step 7 Enter the CUE administrator ID. This is the username to log in to the CUE GUI.
MPORTANT::
IMPORTANT:: Administrator Account Creation
IMPORTANT::
IMPORTANT:: Create an administrator account. With this account,
IMPORTANT:: you can log in to the Cisco Unity Express GUI and
IMPORTANT:: run the initialization wizard.
IMPORTANT::
Enter administrator user ID:
(user ID): Admin
Enter password for admin:
(password): ******
Confirm password for admin by reentering it:
(password): ******
se-172-16-0-0>